[asterisk-users] Dialplan Priorities and Sort Order...

[Danny Nicholas]

Good rewrite, but what about 1877 calls?

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Martin
Sent: Tuesday, May 19, 2009 11:28 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] Dialplan Priorities and Sort Order...

ok, if 18xx are to go through analog lines and the rest through PRI
then it's simply

exten => _18XXNXXXXXX,1,Dial(zap/g1/${EXTEN})
exten => _18XXNXXXXXX,n,Hangup

exten => _1[2-79]XXNXXXXXX,1,Dial(zap/g0/${EXTEN})
exten => _1[2-79]XXNXXXXXX,n,Hangup()

Martin

On Tue, May 19, 2009 at 11:00 AM, Danny Nicholas <danny at debsinc.com> wrote:
> The first _1866 line should start a new segment of the dialplan.  The way
> this should work is 1800 and 1866 go out on zap /g1; anything else falls
> into zap/g0.
>
> -----Original Message-----
> From: asterisk-users-bounces at lists.digium.com
> [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Tim Nelson
> Sent: Tuesday, May 19, 2009 10:38 AM
> To: Asterisk Users Mailing List - Non-Commercial Discussion
> Subject: [asterisk-users] Dialplan Priorities and Sort Order...
>
> Greetings!
>
> I'm hoping someone can help me with what should be the most basic of
> problems. Essentially, I want to have certain calls on an Asterisk 1.2.25
> (Yes I know its old, upgrade, etc... its on my roadmap) install go out a
> couple of analog lines and all other calls go out a PRI. The analog lines
> are setup in Zaptel group 1 and the PRI channels are in Zaptel group 0.
Here
> is my relevant config:
>
> ; Outbound via POTS
> [general-outbound]
> exten => _1800NXXXXXX,1,Dial(ZAP/g1/${EXTEN})
> exten => _1800NXXXXXX,n,Answer
> exten => _1800NXXXXXX,n,Busy
> exten => _1800NXXXXXX,n,Hangup
> exten => _1866NXXXXXX,n,Dial(ZAP/g1/${EXTEN})
> exten => _1866NXXXXXX,n,Answer
> exten => _1866NXXXXXX,n,Busy
> exten => _1866NXXXXXX,n,Hangup
> include => pri_outbound
>
> ; Outbound via PRI
> [pri_outbound]
> exten => _X.,101,Dial(ZAP/g0/${EXTEN})
> exten => _X.,102,Answer
> exten => _X.,103,Busy
> exten => _X.,104,Hangup
>
> I certainly cannot be the only one who wants this sort of setup...
correct?
> Is it the way I'm including the other context, the dial patterns, the
> priorities, etc? I'm not opposed to combining it into a single context, I
> just started it out with this way. All hints are appreciated. (Pun
> intended.. :-) )
>
> --Tim
>
> _______________________________________________
> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
> _______________________________________________
> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>

_______________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users