[Asterisk-video] Trouble making outbound h324m video call
Rene van Weert
rvweert at gmail.com
Tue Apr 1 07:29:15 CDT 2008
Dear Klaus,
After changing pridialplan and prilocaldialplan to international and local
in zapata.conf everything works!
So you were right about the dialplan error in my pri debug. I can dial to a
3G phone and play a video or make a sip call to it, video works just fine...
Thanks very much for your help!
Rene
On Tue, Apr 1, 2008 at 11:11 AM, Klaus Darilion <
klaus.mailinglists at pernau.at> wrote:
> The SETUP message does not contain LCC. MAybe the patch is not applied
> properly? Or wrong zaptel.conf config? Check the config of one of the
> zap channels in the respective trunk, e.g.:
>
> videogw*CLI> zap show channel 1
> Channel: 1I>
> File Descriptor: 17
> Span: 1
> Extension: >
> Dialing: no
> Context: frompstn
> Caller ID: 00436648232115
> Calling TON: 17
> Caller ID name:
> Destroy: 0
> InAlarm: 0
> Signalling Type: ISDN PRI
> Radio: 0
> Owner: <None>
> Real: <None>
> Callwait: <None>
> Threeway: <None>
> Confno: -1
> Propagated Conference: -1
> Real in conference: 0
> DSP: no
> Relax DTMF: no
> Dialing/CallwaitCAS: 0/0
> Default law: alaw
> Fax Handled: no
> Pulse phone: no
> Echo Cancellation: 128 taps unless TDM bridged, currently OFF
> PRI Flags:
> PRI Logical Span: Implicit
> H324M Signalling: use 'Low Layer Compatibility' IE
> ^^^^^^^^^^^^^^^^^^
>
> 1. The line "H324M Signalling" indicates that the patch is applied.
> 2. It should show "use 'Low Layer Compatibility' IE"
>
> Further, as Jose suggested make a proper zaptel config:
> Ext: 0 TON: Unknown Number Type (0) NPI: Unknown Number Plan (0)
>
> Unknown Number Type is ok, but I never saw Unknown Number Plan.
>
> regards
> klaus
>
>
>
>
>
>
> Rene van Weert schrieb:
> > Dear Klaus,
> >
> > I added the line to zapata.conf as you mentioned. However I still get
> > the same result:
> >
> > -- Executing [665 at from-sip:1] h324m_call("SIP/2000-0823bb08",
> > "666 at test <mailto:666 at test>") in new stack
> > -- Executing [666 at test:1] Set("Local/666 at test-23e7,2
> > <mailto:Local/666 at test-23e7,2>", "CHANNEL(transfercapability)=VIDEO") in
> > new stack
> > -- Executing [666 at test:2] NoOp("Local/666 at test-23e7,2
> > <mailto:Local/666 at test-23e7,2>", "transfer=VIDEO") in new stack
> > -- Executing [666 at test:3] Set("Local/666 at test-23e7,2
> > <mailto:Local/666 at test-23e7,2>", "CHANNEL(userinformationlayer1)=38") in
> > new stack
> > -- Executing [666 at test:4] NoOp("Local/666 at test-23e7,2
> > <mailto:Local/666 at test-23e7,2>", "ul1=38") in new stack
> > -- Executing [666 at test:5] Dial("Local/666 at test-23e7,2
> > <mailto:Local/666 at test-23e7,2>", "ZAP/g0/06xxxxxxxx") in new stack
> > -- Making new call for cr 32772
> > -- digital call, setting user information layer 1 to 38 (0x26)
> > -- zap call: h324musellc=0, ast->userinformationlayer1=38
> > -- Requested transfer capability: 0x18 - VIDEO
> > > Protocol Discriminator: Q.931 (8) len=37
> > > Call Ref: len= 2 (reference 4/0x4) (Originator)
> > > Message type: SETUP (5)
> > > [04 03 88 90 a6]
> > > Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer
> > capability: Unrestricted digital information (8)
> > > Ext: 1 Trans mode/rate: 64kbps,
> > circuit-mode (16)
> > > User information layer 1: H.223 and
> > H.245 (38)
> > > [18 03 a9 83 81]
> > > Channel ID (len= 5) [ Ext: 1 IntID: Implicit PRI Spare: 0
> > Exclusive Dchan: 0
> > > ChanSel: Reserved
> > > Ext: 1 Coding: 0 Number Specified Channel
> > Type: 3
> > > Ext: 1 Channel: 1 ]
> > > [6c 06 00 80 32 30 30 30]
> > > Calling Number (len= 8) [ Ext: 0 TON: Unknown Number Type (0) NPI:
> > Unknown Number Plan (0)
> > > Presentation: Presentation permitted, user
> > number not screened (0) '2000' ]
> > > [70 0b 80 30 36 31 35 30 36 34 30 38 30]
> > > Called Number (len=13) [ Ext: 1 TON: Unknown Number Type (0) NPI:
> > Unknown Number Plan (0) '06xxxxxxxx' ]
> > > [a1]skdev*CLI>
> > > Sending Complete (len= 1)
> > q931.c:3245 q931_setup: call 32772 on channel 1 enters state 1 (Call
> > Initiated)
> > -- Called g0/06xxxxxxxx
> > < Protocol Discriminator: Q.931 (8) len=10
> > < Call Ref: len= 2 (reference 4/0x4) (Terminator)
> > < Message type: RELEASE COMPLETE (90)
> > < [08 03 80 e4 04]
> > < Cause (len= 5) [ Ext: 1 Coding: CCITT (ITU) standard (0) Spare: 0
> > Location: User (0)
> > < Ext: 1 Cause: Invalid information element contents
> > (100), class = Protocol Error (e.g. unknown message) (6) ]
> > < Cause data 1: 04 (4)
> > -- Processing IE 8 (cs0, Cause)
> > q931.c:3875 q931_receive: call 32772 on channel 1 enters state 0 (Null)
> > -- Channel 0/1, span 1 got hangup, cause 100
> > NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Null, peerstate Null
> > NEW_HANGUP DEBUG: Destroying the call, ourstate Null, peerstate Null
> > -- Hungup 'Zap/1-1'
> > == Everyone is busy/congested at this time (1:0/0/1)
> > == Auto fallthrough, channel 'Local/666 at test-23e7,2'
> > <mailto:'Local/666 at test-23e7,2'> status is 'CHANUNAVAIL'
> > == Auto fallthrough, channel 'SIP/2000-0823bb08' status is 'UNKNOWN'
> > Kind regards,
> >
> > Rene van Weert
> >
> >
> >
> ------------------------------------------------------------------------
> >
> > _______________________________________________
> > --Bandwidth and Colocation Provided by http://www.api-digital.com--
> >
> > asterisk-video mailing list
> > To UNSUBSCRIBE or update options visit:
> > http://lists.digium.com/mailman/listinfo/asterisk-video
>
> _______________________________________________
> --Bandwidth and Colocation Provided by http://www.api-digital.com--
>
> asterisk-video mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-video
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-video/attachments/20080401/aafe15e1/attachment-0001.htm
More information about the asterisk-video
mailing list