[Asterisk-video] Trouble making outbound h324m video call

[Klaus Darilion]

The SETUP message does not contain LCC. MAybe the patch is not applied 
properly? Or wrong zaptel.conf config? Check the config of one of the 
zap channels in the respective trunk, e.g.:

videogw*CLI> zap show channel 1
Channel: 1I>
File Descriptor: 17
Span: 1
Extension: >
Dialing: no
Context: frompstn
Caller ID: 00436648232115
Calling TON: 17
Caller ID name:
Destroy: 0
InAlarm: 0
Signalling Type: ISDN PRI
Radio: 0
Owner: <None>
Real: <None>
Callwait: <None>
Threeway: <None>
Confno: -1
Propagated Conference: -1
Real in conference: 0
DSP: no
Relax DTMF: no
Dialing/CallwaitCAS: 0/0
Default law: alaw
Fax Handled: no
Pulse phone: no
Echo Cancellation: 128 taps unless TDM bridged, currently OFF
PRI Flags:
PRI Logical Span: Implicit
H324M Signalling: use 'Low Layer Compatibility' IE
^^^^^^^^^^^^^^^^^^

1. The line "H324M Signalling" indicates that the patch is applied.
2. It should show "use 'Low Layer Compatibility' IE"

Further, as Jose suggested make a proper zaptel config:
Ext: 0  TON: Unknown Number Type (0)  NPI: Unknown Number Plan (0)

Unknown Number Type is ok, but I never saw Unknown Number Plan.

regards
klaus






Rene van Weert schrieb:
> Dear Klaus,
>  
> I added the line to zapata.conf as you mentioned. However I still get 
> the same result:
>  
>     -- Executing [665 at from-sip:1] h324m_call("SIP/2000-0823bb08", 
> "666 at test <mailto:666 at test>") in new stack
>     -- Executing [666 at test:1] Set("Local/666 at test-23e7,2 
> <mailto:Local/666 at test-23e7,2>", "CHANNEL(transfercapability)=VIDEO") in 
> new stack
>     -- Executing [666 at test:2] NoOp("Local/666 at test-23e7,2 
> <mailto:Local/666 at test-23e7,2>", "transfer=VIDEO") in new stack
>     -- Executing [666 at test:3] Set("Local/666 at test-23e7,2 
> <mailto:Local/666 at test-23e7,2>", "CHANNEL(userinformationlayer1)=38") in 
> new stack
>     -- Executing [666 at test:4] NoOp("Local/666 at test-23e7,2 
> <mailto:Local/666 at test-23e7,2>", "ul1=38") in new stack
>     -- Executing [666 at test:5] Dial("Local/666 at test-23e7,2 
> <mailto:Local/666 at test-23e7,2>", "ZAP/g0/06xxxxxxxx") in new stack
> -- Making new call for cr 32772
>     -- digital call, setting user information layer 1 to 38 (0x26)
>     -- zap call: h324musellc=0, ast->userinformationlayer1=38
>     -- Requested transfer capability: 0x18 - VIDEO
>  > Protocol Discriminator: Q.931 (8)  len=37
>  > Call Ref: len= 2 (reference 4/0x4) (Originator)
>  > Message type: SETUP (5)
>  > [04 03 88 90 a6]
>  > Bearer Capability (len= 5) [ Ext: 1  Q.931 Std: 0  Info transfer 
> capability: Unrestricted digital information (8)
>  >                              Ext: 1  Trans mode/rate: 64kbps, 
> circuit-mode (16)
>  >                                User information layer 1: H.223 and 
> H.245 (38)
>  > [18 03 a9 83 81]
>  > Channel ID (len= 5) [ Ext: 1  IntID: Implicit  PRI  Spare: 0  
> Exclusive  Dchan: 0
>  >                        ChanSel: Reserved
>  >                       Ext: 1  Coding: 0  Number Specified  Channel 
> Type: 3
>  >                       Ext: 1  Channel: 1 ]
>  > [6c 06 00 80 32 30 30 30]
>  > Calling Number (len= 8) [ Ext: 0  TON: Unknown Number Type (0)  NPI: 
> Unknown Number Plan (0)
>  >                           Presentation: Presentation permitted, user 
> number not screened (0)  '2000' ]
>  > [70 0b 80 30 36 31 35 30 36 34 30 38 30]
>  > Called Number (len=13) [ Ext: 1  TON: Unknown Number Type (0)  NPI: 
> Unknown Number Plan (0)  '06xxxxxxxx' ]
>  > [a1]skdev*CLI>
>  > Sending Complete (len= 1)
> q931.c:3245 q931_setup: call 32772 on channel 1 enters state 1 (Call 
> Initiated)
>     -- Called g0/06xxxxxxxx
> < Protocol Discriminator: Q.931 (8)  len=10
> < Call Ref: len= 2 (reference 4/0x4) (Terminator)
> < Message type: RELEASE COMPLETE (90)
> < [08 03 80 e4 04]
> < Cause (len= 5) [ Ext: 1  Coding: CCITT (ITU) standard (0)  Spare: 0  
> Location: User (0)
> <                  Ext: 1  Cause: Invalid information element contents 
> (100), class = Protocol Error (e.g. unknown message) (6) ]
> <              Cause data 1: 04 (4)
> -- Processing IE 8 (cs0, Cause)
> q931.c:3875 q931_receive: call 32772 on channel 1 enters state 0 (Null)
>     -- Channel 0/1, span 1 got hangup, cause 100
> NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Null, peerstate Null
> NEW_HANGUP DEBUG: Destroying the call, ourstate Null, peerstate Null
>     -- Hungup 'Zap/1-1'
>   == Everyone is busy/congested at this time (1:0/0/1)
>   == Auto fallthrough, channel 'Local/666 at test-23e7,2' 
> <mailto:'Local/666 at test-23e7,2'> status is 'CHANUNAVAIL'
>   == Auto fallthrough, channel 'SIP/2000-0823bb08' status is 'UNKNOWN'
> Kind regards,
>  
> Rene van Weert
> 
> 
> ------------------------------------------------------------------------
> 
> _______________________________________________
> --Bandwidth and Colocation Provided by http://www.api-digital.com--
> 
> asterisk-video mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-video