[Asterisk-Users] TE11OP -> Mitel 200Sx??
Henry Devito
hdevito at mchsi.com
Sun Apr 24 13:47:05 MST 2005
According to the Mitel manuals that version of SX-200D can only use a
regular 24 channel T1. It can not use a PRI interface. You are going to
have to configure * to use a standard T1 not a PRI D4/AMI is the correct
signaling.
----- Original Message -----
From: "Scott Wolfe" <scottwolfe at orbus.net>
To: "Asterisk Users Mailing List - Non-Commercial Discussion"
<asterisk-users at lists.digium.com>
Sent: Sunday, April 24, 2005 11:09 AM
Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
> Thanks Henry,
> -Scott
>
> ----- Original Message -----
> From: "Henry Devito" <hdevito at mchsi.com>
> To: "Asterisk Users Mailing List - Non-Commercial Discussion"
> <asterisk-users at lists.digium.com>
> Sent: Saturday, April 23, 2005 11:05 PM
> Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>
>
>>I am trying to locate the manual for that level software. If it's not
>>here at home it is at my office and I will look everything up in the
>>morning.
>> ----- Original Message -----
>> From: "Scott Wolfe" <scottwolfe at orbus.net>
>> To: "Asterisk Users Mailing List - Non-Commercial Discussion"
>> <asterisk-users at lists.digium.com>; <dwalker at jackson-tube.com>
>> Sent: Saturday, April 23, 2005 9:00 PM
>> Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>>
>>
>>> The Switch is since 1995 and I get a SX-200 Digital G1005 ENH 672P /
>>> F25.0 09-FEB1994 when I look up the software on the switch board so if I
>>> am reading what your telling me then I have to do D4/AMI. So does my
>>> zaptel look correct? Maybe my cableing is off.
>>> Thanks,
>>> -Scott
>>> ----- Original Message -----
>>> From: "Henry Devito" <hdevito at mchsi.com>
>>> To: <dwalker at jackson-tube.com>; "Asterisk Users Mailing List -
>>> Non-Commercial Discussion" <asterisk-users at lists.digium.com>
>>> Sent: Friday, April 22, 2005 8:34 PM
>>> Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>>>
>>>
>>>> Of course there are exceptions to the rules. I see now on a couple
>>>> software releases where they do allow PRI with D4/AMI and PRI with
>>>> esf/b8zs. It's been a year or so since I messed with trunking on a
>>>> 200, I've mostly been installing and maintaining the SX2000's and
>>>> 3300's.
>>>>
>>>> Henry
>>>>
>>>>
>>>>
>>>> ----- Original Message -----
>>>> From: "Dennis Walker" <dwalker at jackson-tube.com>
>>>> To: "'Asterisk Users Mailing List - Non-Commercial Discussion'"
>>>> <asterisk-users at lists.digium.com>
>>>> Sent: Friday, April 22, 2005 9:13 PM
>>>> Subject: RE: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>>>>
>>>>
>>>>>I have done the same thing with an sx200 and a pri circuit
>>>>>
>>>>> My sx200 can only do ami d4 and e&m channels
>>>>>
>>>>> Here's parts of my config that takes the pri and converts it to e&m
>>>>> with
>>>>> ANI & DNIS
>>>>>
>>>>> zaptel.conf
>>>>>
>>>>> # t1 connected to the PRI circuit
>>>>> span=1,1,0,exf,b8zs
>>>>>
>>>>> # t1 connected to SX200
>>>>> # the t1 card on my sx200 did d4 ami and I supplied ANI and DNIS
>>>>> through
>>>>> the dial plan
>>>>>
>>>>> span=2,0,0,d4,ami
>>>>>
>>>>> bchan=1-23
>>>>> dchan=24
>>>>> e&m=25-47
>>>>> ---------------------------------------------
>>>>> zapata.conf
>>>>>
>>>>> [channels]
>>>>>
>>>>> echocancel=yes
>>>>> echocancelwhenbridged=yes
>>>>> echotraining=no
>>>>> rxgain=0.0
>>>>> txgain=0.0
>>>>> useincomingcalleridonzaptransfer=yes
>>>>> restrictcid=no
>>>>> context=default
>>>>> usecallingpres=yes
>>>>> usercallerid=yes
>>>>> hidecallerid=no
>>>>> callerid="Company Name"<8005551212>
>>>>> signalling=pri_cpe
>>>>> switchtype=dms100
>>>>> group=1
>>>>> channel => 1-23
>>>>>
>>>>> group=2
>>>>> signalling=em_w
>>>>> emdigitwait=500
>>>>> channel => 24-47
>>>>>
>>>>> # I needed the emdigitwait=500 to wait long enough for the SX200 to
>>>>> dial
>>>>> out it's digits
>>>>>
>>>>>
>>>>> --------------------------------------------------
>>>>> extensions.conf
>>>>>
>>>>> # our PRI circiut gave us the last 4 digits of the dialed number and
>>>>> this
>>>>> is how I passed
>>>>> # *ANI*DNIS* to the SX200 for it to decode
>>>>>
>>>>> # the first group were individual numbers that mapped to faxes and
>>>>> modems
>>>>>
>>>>> exten => 1234,1,Dial(Zap/g2/*${CALLERIDNUM}*${EXTEN}*,,r)
>>>>> exten => 5555,1,Dial(Zap/g2/*${CALLERIDNUM}*${EXTEN}*,,r)
>>>>> exten => 3333,1,Dial(Zap/g2/*${CALLERIDNUM}*${EXTEN}*,,r)
>>>>>
>>>>> # this set mapped our did 5000 - 5199 to the SX200
>>>>>
>>>>> exten => _5[0-1]XX,1,Dial(Zap/g2/*${CALLERIDNUM}*${EXTEN}*,,r)
>>>>>
>>>>> The reset of the dial plan took what ever I set up in the sx200 ARS to
>>>>> dial
>>>>> out and
>>>>> sent out put Zap/G1
>>>>>
>>>>>
>>>>> Hope this helps
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> ----------
>>>>> From: Henry Devito[SMTP:hdevito at mchsi.com]
>>>>> Reply To: Asterisk Users Mailing List - Non-Commercial Discussion
>>>>> Sent: Friday, April 22, 2005 8:56 PM
>>>>> To: Scott Wolfe; Asterisk Users Mailing List - Non-Commercial
>>>>> Discussion
>>>>> Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>>>>>
>>>>> <<File: ATT00262.html>><<File: ATT00263.txt>>
>>>>> I was wrong. I just looked in my Mitel I&M's. What level software
>>>>> are you
>>>>> on in the SX200? Up until a certain level 200's could only do D4/AMI
>>>>> T1's,
>>>>> they could not do PRI's. If it is a newer switch within the past 3
>>>>> years
>>>>> or an older switch with later software than you can do PRI, but the
>>>>> signaling and framing must be ESF/B8ZS.
>>>>>
>>>>> Henry
>>>>> ----- Original Message -----
>>>>> From: Scott Wolfe
>>>>> To: mike at shelcomm.com ; Asterisk Users Mailing List - Non-Commercial
>>>>> Discussion
>>>>> Sent: Friday, April 22, 2005 7:04 PM
>>>>> Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> Thanks,
>>>>> This is what I have now, but my Mitel PBX and Asterisk Box are
>>>>> unable
>>>>> to communicate via the T1 connection. Asterisk loads ok but I get
>>>>> error
>>>>> lights (blinking orange) on my TE110P and on my Mitel T1 card. Hummmm
>>>>>
>>>>>
>>>>> -Scott
>>>>>
>>>>> /etc/zaptel.conf
>>>>> loadzone = us
>>>>> defaultzone=us
>>>>> span=1,0,0,d4,ami
>>>>> bchan=1-23
>>>>> dchan=24
>>>>>
>>>>> /etc/asterisk/zapata.conf
>>>>> [trunkgroups]
>>>>>
>>>>> [channels]
>>>>> context=default
>>>>> switchtype=dms100
>>>>> rxwink=300
>>>>> usecallerid=no
>>>>> hidecallerid=no
>>>>> callwaiting=no
>>>>> usecallingpres=yes
>>>>> callwaitingcallerid=no
>>>>> threewaycalling=yes
>>>>> transfer=yes
>>>>> canpark=yes
>>>>> cancallforward=yes
>>>>> callreturn=yes
>>>>> echocancel=yes
>>>>> echocancelwhenbridged=yes
>>>>> rxgain=0.0 ;into the pstn twords the telco
>>>>> txgain=0.0
>>>>> callgroup=1
>>>>> pickupgroup=1
>>>>> immediate=yes
>>>>>
>>>>> signalling=pri_cpe
>>>>> group=1
>>>>> context=default
>>>>> emdigitwait=500
>>>>> channel => 1-23 ; Set this to 1-15,17-31 for E1
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> ----- Original Message -----
>>>>> From: Michael D Schelin
>>>>> To: Asterisk Users Mailing List - Non-Commercial Discussion
>>>>> Sent: Friday, April 22, 2005 4:48 PM
>>>>> Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>>>>>
>>>>>
>>>>> Hello Henry
>>>>> e&m=1-23 should be bchan=1-23
>>>>> you have it set for analog
>>>>> also
>>>>> signaling=pri_cpe
>>>>>
>>>>>
>>>>> Henry Devito wrote:
>>>>>
>>>>> Don't you need one of these directives so the PRI knows which is
>>>>> master and which is slave?
>>>>>
>>>>> a.. pri_cpe: PRI signaling, CPE side
>>>>> a.. pri_net: PRI signaling, Network side
>>>>>
>>>>> Henry
>>>>> ----- Original Message -----
>>>>> From: Scott Wolfe
>>>>> To: Asterisk-Users at lists.digium.com
>>>>> Sent: Friday, April 22, 2005 11:01 AM
>>>>> Subject: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>>>>>
>>>>>
>>>>> Hello all. I just received a TE110P and am trying to hook it to
>>>>> my
>>>>> Mitel 200SX has anyone successfully done this? My configuration is as
>>>>> follows.
>>>>>
>>>>>
>>>>> Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card.
>>>>>
>>>>>
>>>>> All I get is a blinking yellow on my TE110P card and an alarm
>>>>> on my
>>>>> Mitel. T1 card.
>>>>>
>>>>>
>>>>> Any advice would be great.
>>>>>
>>>>>
>>>>> Zaptel.conf
>>>>>
>>>>> span=1,0,1,d4,ami
>>>>>
>>>>> e&m=1-23
>>>>>
>>>>> dchan=24
>>>>>
>>>>>
>>>>> Zapata.conf
>>>>>
>>>>> signalling=em_w
>>>>>
>>>>> switchtype=dms100
>>>>>
>>>>> echocancel=yes
>>>>>
>>>>> echocancelwhenbridged=yes
>>>>>
>>>>> echotraining=400
>>>>>
>>>>> callerid=asreceived
>>>>>
>>>>> group=1
>>>>>
>>>>> context=default
>>>>>
>>>>> channel => 1-23
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> ------------------------------------------------------------------------
>>>>> _______________________________________________
>>>>> Asterisk-Users mailing list
>>>>> Asterisk-Users at lists.digium.com
>>>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>> To UNSUBSCRIBE or update options visit:
>>>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>> --------------------------------------------------------------------------
>>>>> _______________________________________________
>>>>> Asterisk-Users mailing list
>>>>> Asterisk-Users at lists.digium.com
>>>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>> To UNSUBSCRIBE or update options visit:
>>>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>>
>>>>>
>>>>>
>>>>> ------------------------------------------------------------------------
>>>>> ----
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> Asterisk-Users mailing list
>>>>> Asterisk-Users at lists.digium.com
>>>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>> To UNSUBSCRIBE or update options visit:
>>>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>>
>>>>>
>>>>> ------------------------------------------------------------------------
>>>>> ------
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> Asterisk-Users mailing list
>>>>> Asterisk-Users at lists.digium.com
>>>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>> To UNSUBSCRIBE or update options visit:
>>>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>>
>>>>> _______________________________________________
>>>>> Asterisk-Users mailing list
>>>>> Asterisk-Users at lists.digium.com
>>>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>> To UNSUBSCRIBE or update options visit:
>>>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>
>>>> _______________________________________________
>>>> Asterisk-Users mailing list
>>>> Asterisk-Users at lists.digium.com
>>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>> To UNSUBSCRIBE or update options visit:
>>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>
>>> _______________________________________________
>>> Asterisk-Users mailing list
>>> Asterisk-Users at lists.digium.com
>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>> To UNSUBSCRIBE or update options visit:
>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>
>> _______________________________________________
>> Asterisk-Users mailing list
>> Asterisk-Users at lists.digium.com
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>> To UNSUBSCRIBE or update options visit:
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
More information about the asterisk-users
mailing list