[asterisk-users] Problems with Digium TE110P
Antonio Carlos Theophilo Costa Junior
antonio at paggo.com.br
Fri Apr 27 10:34:32 MST 2007
Hi everyone
I have a Digium card TE110P and after plug it, turn on the computer and
configure, the LEDs don't light up in spite of what Digium FAQ says about the
LEDs:
When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP?
... The TE110P LED's will light up RED when the span is configured and kernel
module is loaded. If configured correctly and a circuit or channel bank is
connected the LED should turn GREEN.
...
Below are the output of dmesg, lsmod, /etc/zaptel.conf and ztcfg -vvv. Did
anyone have this problem before?
Thanks
Antônio Theóphilo Júnior
root at paggo-asterisk01:~# dmesg | more
...
[42949385.790000] Zapata Telephony Interface Registered on major 196
[42949385.790000] Zaptel Version: 1.2.10 Echo Canceller: KB1
[42949385.840000] e100: Intel(R) PRO/100 Network Driver, 3.4.14-k4-NAPI
[42949385.840000] e100: Copyright(c) 1999-2005 Intel Corporation
[42949385.960000] intel8x0_measure_ac97_clock: measured 61046 usecs
[42949385.960000] intel8x0: clocking to 48000
[42949385.970000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 21 (level, low)
-> IRQ 209
[42949385.970000] Controller version: 24
[42949385.970000] FALC version: 00000000
[42949385.970000] TE110P: Setting up global serial parameters for E1 FALC V1.2
[42949385.970000] TE110P: Successfully initialized serial bus for card
[42949385.970000] Found a Wildcard: Digium Wildcard TE110P T1/E1
[42949386.000000] ACPI: PCI Interrupt 0000:01:08.0[A] -> GSI 20 (level, low)
-> IRQ 217
[42949386.020000] e100: eth0: e100_probe: addr 0xff8fe000, irq 217, MAC addr
00:0C:F1:E7:1B:0B
[42949386.060000] Registered tone zone 20 (Brazil)
[42949386.060000] TE110P: Span configured for CAS/HDB3
[42949386.060000] Calling startup (flags is 4099)
[42949386.100000] CSLIP: code copyright 1989 Regents of the University of
California
[42949386.130000] ISDN subsystem Rev:
1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
[42949386.190000] HiSax: Linux Driver for passive ISDN cards
[42949386.190000] HiSax: Version 3.5 (module)
[42949386.190000] HiSax: Layer1 Revision 2.46.2.5
[42949386.190000] HiSax: Layer2 Revision 2.30.2.4
[42949386.190000] HiSax: TeiMgr Revision 2.20.2.3
[42949386.190000] HiSax: Layer3 Revision 2.22.2.3
[42949386.190000] HiSax: LinkLayer Revision 2.59.2.4
[42949386.380000] lp0: using parport0 (interrupt-driven).
...
root at paggo-asterisk01:~# lsmod
Module Size Used by
ipv6 287584 24
ext3 147848 1
jbd 62996 1 ext3
dm_mod 63512 1
md_mod 76756 0
lp 13220 0
hisax 575824 0
isdn 153056 1 hisax
slhc 8320 1 isdn
e100 43012 0
mii 7040 1 e100
wcte11xp 27424 0
zaptel 192900 1 wcte11xp
crc_ccitt 3200 2 hisax,zaptel
snd_intel8x0 36380 0
snd_ac97_codec 100512 1 snd_intel8x0
snd_ac97_bus 3328 1 snd_ac97_codec
snd_pcm_oss 56992 0
snd_mixer_oss 21248 1 snd_pcm_oss
snd_pcm 96516 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 27140 1 snd_pcm
i2c_i810 6276 0
i2c_algo_bit 10760 1 i2c_i810
hw_random 6420 0
psmouse 40836 0
snd 59748 6
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 11232 1 snd
snd_page_alloc 12296 2 snd_intel8x0,snd_pcm
i2c_core 23296 1 i2c_algo_bit
shpchp 50144 0
pci_hotplug 30652 1 shpchp
intel_agp 25628 1
agpgart 37580 1 intel_agp
parport_pc 38724 1
parport 39624 2 lp,parport_pc
serio_raw 8580 0
pcspkr 3204 0
floppy 65252 0
evdev 11136 0
xfs 648156 10
exportfs 7296 1 xfs
ide_generic 2432 0
ehci_hcd 34824 0
uhci_hcd 35984 0
usbcore 137732 3 ehci_hcd,uhci_hcd
ide_cd 36740 0
cdrom 42272 1 ide_cd
ide_disk 19968 13
piix 12420 1
generic 5892 0
thermal 14728 0
processor 27080 1 thermal
fan 5764 0
capability 5896 0
commoncap 8192 1 capability
vga16fb 14856 1
vgastate 11136 1 vga16fb
fbcon 44448 70
tileblit 3712 1 fbcon
font 9216 1 fbcon
bitblit 7424 1 fbcon
softcursor 3200 1 bitblit
root at paggo-asterisk01:~# more /etc/zaptel.conf | egrep -v '^#'
span=1,0,0,cas,hdb3
cas=1-15:1001
dchan=16
cas=17-31:1001
loadzone=br
defaultzone=br
root at paggo-asterisk01:~# ztcfg -vvvv
Zaptel Configuration
======================
SPAN 1: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
Channel map:
Channel 01: CAS / User (Default) (Slaves: 01)
Channel 02: CAS / User (Default) (Slaves: 02)
Channel 03: CAS / User (Default) (Slaves: 03)
Channel 04: CAS / User (Default) (Slaves: 04)
Channel 05: CAS / User (Default) (Slaves: 05)
Channel 06: CAS / User (Default) (Slaves: 06)
Channel 07: CAS / User (Default) (Slaves: 07)
Channel 08: CAS / User (Default) (Slaves: 08)
Channel 09: CAS / User (Default) (Slaves: 09)
Channel 10: CAS / User (Default) (Slaves: 10)
Channel 11: CAS / User (Default) (Slaves: 11)
Channel 12: CAS / User (Default) (Slaves: 12)
Channel 13: CAS / User (Default) (Slaves: 13)
Channel 14: CAS / User (Default) (Slaves: 14)
Channel 15: CAS / User (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: CAS / User (Default) (Slaves: 17)
Channel 18: CAS / User (Default) (Slaves: 18)
Channel 19: CAS / User (Default) (Slaves: 19)
Channel 20: CAS / User (Default) (Slaves: 20)
Channel 21: CAS / User (Default) (Slaves: 21)
Channel 22: CAS / User (Default) (Slaves: 22)
Channel 23: CAS / User (Default) (Slaves: 23)
Channel 24: CAS / User (Default) (Slaves: 24)
Channel 25: CAS / User (Default) (Slaves: 25)
Channel 26: CAS / User (Default) (Slaves: 26)
Channel 27: CAS / User (Default) (Slaves: 27)
Channel 28: CAS / User (Default) (Slaves: 28)
Channel 29: CAS / User (Default) (Slaves: 29)
Channel 30: CAS / User (Default) (Slaves: 30)
Channel 31: CAS / User (Default) (Slaves: 31)
31 channels configured.
Esta mensagem pode conter informacao confidencial e/ou privilegiada.
Se voce nao for o destinatario ou a pessoa autorizada a receber esta mensagem, nao pode usar, copiar ou divulgar as informacoes nela contidas ou tomar qualquer acao baseada nessas informacoes.
Se voce recebeu esta mensagem por engano, por favor avise imediatamente o remetente, respondendo o e-mail e em seguida apague-o. Agradecemos sua cooperacao.
This message may contain confidential or privileged information. If you are not the addressee or authorized to receive this for the addressee, you must not use, copy, disclose or take any action based on this message or any
information herein. If you have received this message in error, please advise the sender immediately by reply e-mail and delete this message. Thank you for your cooperation.
More information about the asterisk-users
mailing list