[Asterisk-Users] CHAN_CAPI problem
Armin Schindler
armin at melware.de
Tue Jan 10 11:16:06 MST 2006
On Tue, 10 Jan 2006 asterisk at frameweb.it wrote:
> Thank you.
> I already downloaded and installed it (they are dated 07-01-2006, version
> 0.6.3, correct ?)
Yes.
> I maked clean, make and make install.
>
> Nothing changed, dial out perfect, dial in: (capi debug on)
>
> asteriskge03*CLI> capi info
> Contr1: 2 B channels total, 2 B channels free.
> asteriskge03*CLI>
> asteriskge03*CLI>
> -- CONNECT_IND
> (PLCI=0x101,DID=104695467,CID=108680550,CIP=0x1,CONTROLLER=0x1)
> == BRI1: Interface cleanup PLCI=0x101
>
> BRI1 is the name of my interface
>
> could it be a kernel issue ?? I am using SUSE Linux 10;
I don't think so. Please increase the the verbose level to 5
(set verbose 5) in addition to 'capi debug'.
Armin
> kernel : 2.6.13-15.7-smp
>
> Andrea
>
>
>
>
> Armin Schindler
> <armin at melware.de
> > To
> Sent by: Asterisk Users Mailing List -
> asterisk-users-bo Non-Commercial Discussion
> unces at lists.digiu <asterisk-users at lists.digium.com>
> m.com cc
>
> Subject
> 10/01/2006 18.29 Re: [Asterisk-Users] CHAN_CAPI
> problem
>
> Please respond to
> Asterisk Users
> Mailing List -
> Non-Commercial
> Discussion
> <asterisk-users at l
> ists.digium.com>
>
>
>
>
>
>
> I suggest you use the newer chan_capi-cm (loadable from sourceforge.net).
>
> Armin
>
> On Tue, 10 Jan 2006 asterisk at frameweb.it wrote:
> > Hi all,
> > I installed asterisk stable cvs 1.2 and chan_capi 0.4.0 PRE1, with one
> AVM
> > Fritz Card ISDN connected to a Telecom NT1 Plus
> >
> > I configured asterisk via AMP.
> > No problem in making calls.
> > If I try to ring the ISDN Phone Number, I don't see anything on the
> > asterisk Console,
> > I I activate the capi debug , I see the ring on the capi channel.
> > If the context were wrong , I anyway should see some line about this....
> >
> > Why I cannot see anything on asterisk ,nor in the /var/log/asterisk/full
> ?
> >
> > here is my /etc/asterisk/capi.conf
> >
> > asteriskge03:/etc/asterisk # cat capi.conf
> > ;
> > ; CAPI config
> > ;
> > ;
> >
> > ; general section
> >
> > [general]
> > nationalprefix=0
> > internationalprefix=00
> > rxgain=0.8
> > txgain=0.8
> > ;ulaw=yes ;set this, if you live in u-law world instead of a-law
> >
> > ; interface sections ...
> >
> > [BRI1] ;this example interface gets name 'ISDN1' and may be any
> > ;name not starting with 'g' or 'contr'.
> > ;ntmode=yes ;if isdn card operates in nt mode, set this to yes
> > isdnmode=msn ;'MSN' (point-to-multipoint) or 'DID' (direct inward
> dial)
> > ;when using NT-mode, 'DID' should be set in any case
> > incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * = any
> > ;defaultcid=123 ;set a default caller id to that interface for dial-out,
> > ;this caller id will be used when dial option 'd' is
> set.
> > ;controller=0 ;ISDN4BSD default
> > ;controller=7 ;ISDN4BSD USB default
> > controller=1 ;capi controller number to use
> > group=1 ;dialout group
> > ;prefix=0 ;set a prefix to calling number on incoming calls
> > softdtmf=on ;enable/disable software dtmf detection, recommended for
> > AVM cards
> > relaxdtmf=on ;in addition to softdtmf, you can use relaxed dtmf
> > detection
> > accountcode= ;Asterisk accountcode to use in CDRs
> > context=from-pstn ;context for incoming calls
> > holdtype=hold ;when Asterisk puts the call on hold, ISDN HOLD will be
> > used. If
> > ;set to 'local' (default value), no hold is done and
> > Asterisk may
> > ;play MOH.
> > ;immediate=yes ;DID: immediate start of pbx with extension 's' if no
> > digits were
> > ; received on incoming call (no destination number
> > yet)
> > ;MSN: start pbx on CONNECT_IND and don't wait for
> > SETUP/SENDING-COMPLETE.
> > ; info like REDIRECTINGNUMBER may be lost, but this
> is
> > necessary for
> > ; drivers/pbx/telco which does not send SETUP or
> > SENDING-COMPLETE.
> > ;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression
> > ;echocancel=yes ;EICON DIVA SERVER (CAPI) echo cancelation
> > ;(possible values: 'no', 'yes', 'force', 'g164', 'g165')
> > echocancelold=yes;use facility selector 6 instead of correct 8 (necessary
> > for older eicon drivers)
> > ;echotail=64 ;echo cancel tail setting
> > ;bridge=yes ;native bridging (CAPI line interconnect) if available
> > ;callgroup=1 ;Asterisk call group
> > devices=2 ;number of concurrent calls on this controller
> > ;(2 makes sense for single BRI, 30 for PRI)
> >
> > thanks in advance,
> > Andrea
> >
> > Chi ricevesse questa mail per errore e' gentilmente pregato di
> cancellarla.
> >
> > Visitate il sito http://www.frameweb.it
> >
> > _______________________________________________
> > --Bandwidth and Colocation provided by Easynews.com --
> >
> > Asterisk-Users mailing list
> > To UNSUBSCRIBE or update options visit:
> > http://lists.digium.com/mailman/listinfo/asterisk-users
> >
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
More information about the asterisk-users
mailing list