[Asterisk-Users] CHAN_CAPI problem

Wed Jan 11 01:35:51 MST 2006

Thank you very much for your attention;
Here is what you asked for:
***********************************************************************************
asteriskge03*CLI> set verbose 15
Verbosity is at least 15
asteriskge03*CLI> capi debug
CAPI Debugging Enabled
asteriskge03*CLI> capi info
Contr1: 2 B channels total, 2 B channels free.

CONNECT_IND ID=002 #0x2011 LEN=0047
  Controller/PLCI/NCCI            = 0x101
  CIPValue                        = 0x1
  CalledPartyNumber               = <a1>104695467
  CallingPartyNumber              = <21 81>108680550
  CalledPartySubaddress           = default
  CallingPartySubaddress          = default
  BC                              = <80 90 a3>
  LLC                             = default
  HLC                             = default
  AdditionalInfo                  = default

    -- CONNECT_IND
(PLCI=0x101,DID=104695467,CID=108680550,CIP=0x1,CONTROLLER=0x1)
       > BRI1: msn='*' DNID='104695467' MSN
  == BRI1: Incoming call '0108680550' -> '104695467'
INFO_IND ID=002 #0x2012 LEN=0017
  Controller/PLCI/NCCI            = 0x101
  InfoNumber                      = 0x1e
  InfoElement                     = <82 81>

INFO_RESP ID=002 #0x2012 LEN=0012
  Controller/PLCI/NCCI            = 0x101

    -- BRI1: info element PI 82 81
       > BRI1: Not end-to-end ISDN
INFO_IND ID=002 #0x2013 LEN=0025
  Controller/PLCI/NCCI            = 0x101
  InfoNumber                      = 0x70
  InfoElement                     = <a1>104695467

INFO_RESP ID=002 #0x2013 LEN=0012
  Controller/PLCI/NCCI            = 0x101

    -- BRI1: info element CALLED PARTY NUMBER
       > BRI1: INFO_IND DID digits not used in this state.
INFO_IND ID=002 #0x2014 LEN=0016
  Controller/PLCI/NCCI            = 0x101
  InfoNumber                      = 0x18
  InfoElement                     = <89>

INFO_RESP ID=002 #0x2014 LEN=0012
  Controller/PLCI/NCCI            = 0x101

    -- BRI1: info element CHANNEL IDENTIFICATION 89
DISCONNECT_IND ID=002 #0x2017 LEN=0014
  Controller/PLCI/NCCI            = 0x101
  Reason                          = 0x0

DISCONNECT_RESP ID=002 #0x2017 LEN=0012
  Controller/PLCI/NCCI            = 0x101

    -- BRI1: DISCONNECT_IND on incoming without pbx, doing hangup.
  == BRI1: CAPI Hangingup
  == BRI1: Interface cleanup PLCI=0x101
       > CAPI devicestate requested for BRI1/104695467

***********************************************************************************

The lines:

BRI1: DISCONNECT_IND on incoming without pbx, doing hangup.
  == BRI1: CAPI Hangingup
  == BRI1: Interface cleanup PLCI=0x101
       > CAPI devicestate requested for BRI1/104695467

appeared on the console WHILE I was still earing the ring tone on the
calling phone. When I , at last, after other 4 rings, hangup the calling
phone,
nothing changed on the console

Andrea

             Armin Schindler                                               
             <armin at melware.de                                             
             >                                                          To 
             Sent by:                  Asterisk Users Mailing List -       
             asterisk-users-bo         Non-Commercial Discussion           
             unces at lists.digiu         <asterisk-users at lists.digium.com>   
             m.com                                                      cc 

                                                                   Subject 
             10/01/2006 19.16          Re: [Asterisk-Users] CHAN_CAPI      
                                       problem                             

             Please respond to                                             
              Asterisk Users                                               
              Mailing List -                                               
              Non-Commercial                                               
                Discussion                                                 
             <asterisk-users at l                                             
             ists.digium.com>                                              

On Tue, 10 Jan 2006 asterisk at frameweb.it wrote:
> Thank you.
> I already downloaded and installed it (they are dated 07-01-2006, version
> 0.6.3, correct ?)

Yes.

> I maked clean, make and make install.
>
> Nothing changed, dial out perfect, dial in: (capi debug on)
>
> asteriskge03*CLI> capi info
> Contr1: 2 B channels total, 2 B channels free.
> asteriskge03*CLI>
> asteriskge03*CLI>
>     -- CONNECT_IND
> (PLCI=0x101,DID=104695467,CID=108680550,CIP=0x1,CONTROLLER=0x1)
>   == BRI1: Interface cleanup PLCI=0x101
>
> BRI1 is the name of my interface
>
> could it be a kernel issue ?? I am using SUSE Linux 10;

I don't think so. Please increase the the verbose level to 5
(set verbose 5) in addition to 'capi debug'.

Armin

> kernel :  2.6.13-15.7-smp
>
> Andrea
>
>
>
>

>              Armin Schindler

>              <armin at melware.de

>              >
To
>              Sent by:                  Asterisk Users Mailing List -

>              asterisk-users-bo         Non-Commercial Discussion

>              unces at lists.digiu         <asterisk-users at lists.digium.com>

>              m.com
cc
>

>
Subject
>              10/01/2006 18.29          Re: [Asterisk-Users] CHAN_CAPI

>                                        problem

>

>              Please respond to

>               Asterisk Users

>               Mailing List -

>               Non-Commercial

>                 Discussion

>              <asterisk-users at l

>              ists.digium.com>

>

>

>
>
>
>
> I suggest you use the newer chan_capi-cm (loadable from sourceforge.net).
>
> Armin
>
> On Tue, 10 Jan 2006 asterisk at frameweb.it wrote:
> > Hi all,
> > I installed asterisk stable cvs 1.2 and chan_capi 0.4.0 PRE1, with one
> AVM
> > Fritz Card ISDN connected to a Telecom NT1 Plus
> >
> > I configured asterisk via AMP.
> > No problem in making calls.
> > If I try to ring the ISDN Phone Number, I don't see anything on the
> > asterisk Console,
> > I I activate the capi debug , I see the ring on the capi channel.
> > If the context were wrong , I anyway should  see some line about
this....
> >
> > Why I cannot see anything on asterisk ,nor in the
/var/log/asterisk/full
> ?
> >
> > here is my /etc/asterisk/capi.conf
> >
> > asteriskge03:/etc/asterisk # cat capi.conf
> > ;
> > ; CAPI config
> > ;
> > ;
> >
> > ; general section
> >
> > [general]
> > nationalprefix=0
> > internationalprefix=00
> > rxgain=0.8
> > txgain=0.8
> > ;ulaw=yes        ;set this, if you live in u-law world instead of a-law
> >
> > ; interface sections ...
> >
> > [BRI1]          ;this example interface gets name 'ISDN1' and may be
any
> >                  ;name not starting with 'g' or 'contr'.
> > ;ntmode=yes      ;if isdn card operates in nt mode, set this to yes
> > isdnmode=msn     ;'MSN' (point-to-multipoint) or 'DID' (direct inward
> dial)
> >                  ;when using NT-mode, 'DID' should be set in any case
> > incomingmsn=*    ;allow incoming calls to this list of MSNs/DIDs, * =
any
> > ;defaultcid=123  ;set a default caller id to that interface for
dial-out,
> >                  ;this caller id will be used when dial option 'd' is
> set.
> > ;controller=0    ;ISDN4BSD default
> > ;controller=7    ;ISDN4BSD USB default
> > controller=1     ;capi controller number to use
> > group=1          ;dialout group
> > ;prefix=0        ;set a prefix to calling number on incoming calls
> > softdtmf=on      ;enable/disable software dtmf detection, recommended
for
> > AVM cards
> > relaxdtmf=on     ;in addition to softdtmf, you can use relaxed dtmf
> > detection
> > accountcode=     ;Asterisk accountcode to use in CDRs
> > context=from-pstn  ;context for incoming calls
> > holdtype=hold    ;when Asterisk puts the call on hold, ISDN HOLD will
be
> > used. If
> >                  ;set to 'local' (default value), no hold is done and
> > Asterisk may
> >                  ;play MOH.
> > ;immediate=yes   ;DID: immediate start of pbx with extension 's' if no
> > digits were
> >                  ;     received on incoming call (no destination number
> > yet)
> >                  ;MSN: start pbx on CONNECT_IND and don't wait for
> > SETUP/SENDING-COMPLETE.
> >                  ;     info like REDIRECTINGNUMBER may be lost, but
this
> is
> > necessary for
> >                  ;     drivers/pbx/telco which does not send SETUP or
> > SENDING-COMPLETE.
> > ;echosquelch=1   ;_VERY_PRIMITIVE_ echo suppression
> > ;echocancel=yes  ;EICON DIVA SERVER (CAPI) echo cancelation
> >                  ;(possible values: 'no', 'yes', 'force', 'g164',
'g165')
> > echocancelold=yes;use facility selector 6 instead of correct 8
(necessary
> > for older eicon drivers)
> > ;echotail=64     ;echo cancel tail setting
> > ;bridge=yes      ;native bridging (CAPI line interconnect) if available
> > ;callgroup=1     ;Asterisk call group
> > devices=2        ;number of concurrent calls on this controller
> >                  ;(2 makes sense for single BRI, 30 for PRI)
> >
> > thanks in advance,
> > Andrea
> >
> > Chi ricevesse questa mail per errore e' gentilmente pregato di
> cancellarla.
> >
> > Visitate il sito http://www.frameweb.it
> >
> > _______________________________________________
> > --Bandwidth and Colocation provided by Easynews.com --
> >
> > Asterisk-Users mailing list
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-users
> >
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users