[Asterisk-Users] CHAN_CAPI problem

[Armin Schindler]

I suggest you use the newer chan_capi-cm (loadable from sourceforge.net).

Armin

On Tue, 10 Jan 2006 asterisk at frameweb.it wrote:
> Hi all,
> I installed asterisk stable cvs 1.2 and chan_capi 0.4.0 PRE1, with one AVM
> Fritz Card ISDN connected to a Telecom NT1 Plus
> 
> I configured asterisk via AMP.
> No problem in making calls.
> If I try to ring the ISDN Phone Number, I don't see anything on the
> asterisk Console,
> I I activate the capi debug , I see the ring on the capi channel.
> If the context were wrong , I anyway should  see some line about this....
> 
> Why I cannot see anything on asterisk ,nor in the /var/log/asterisk/full  ?
> 
> here is my /etc/asterisk/capi.conf
> 
> asteriskge03:/etc/asterisk # cat capi.conf
> ;
> ; CAPI config
> ;
> ;
> 
> ; general section
> 
> [general]
> nationalprefix=0
> internationalprefix=00
> rxgain=0.8
> txgain=0.8
> ;ulaw=yes        ;set this, if you live in u-law world instead of a-law
> 
> ; interface sections ...
> 
> [BRI1]          ;this example interface gets name 'ISDN1' and may be any
>                  ;name not starting with 'g' or 'contr'.
> ;ntmode=yes      ;if isdn card operates in nt mode, set this to yes
> isdnmode=msn     ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
>                  ;when using NT-mode, 'DID' should be set in any case
> incomingmsn=*    ;allow incoming calls to this list of MSNs/DIDs, * = any
> ;defaultcid=123  ;set a default caller id to that interface for dial-out,
>                  ;this caller id will be used when dial option 'd' is set.
> ;controller=0    ;ISDN4BSD default
> ;controller=7    ;ISDN4BSD USB default
> controller=1     ;capi controller number to use
> group=1          ;dialout group
> ;prefix=0        ;set a prefix to calling number on incoming calls
> softdtmf=on      ;enable/disable software dtmf detection, recommended for
> AVM cards
> relaxdtmf=on     ;in addition to softdtmf, you can use relaxed dtmf
> detection
> accountcode=     ;Asterisk accountcode to use in CDRs
> context=from-pstn  ;context for incoming calls
> holdtype=hold    ;when Asterisk puts the call on hold, ISDN HOLD will be
> used. If
>                  ;set to 'local' (default value), no hold is done and
> Asterisk may
>                  ;play MOH.
> ;immediate=yes   ;DID: immediate start of pbx with extension 's' if no
> digits were
>                  ;     received on incoming call (no destination number
> yet)
>                  ;MSN: start pbx on CONNECT_IND and don't wait for
> SETUP/SENDING-COMPLETE.
>                  ;     info like REDIRECTINGNUMBER may be lost, but this is
> necessary for
>                  ;     drivers/pbx/telco which does not send SETUP or
> SENDING-COMPLETE.
> ;echosquelch=1   ;_VERY_PRIMITIVE_ echo suppression
> ;echocancel=yes  ;EICON DIVA SERVER (CAPI) echo cancelation
>                  ;(possible values: 'no', 'yes', 'force', 'g164', 'g165')
> echocancelold=yes;use facility selector 6 instead of correct 8 (necessary
> for older eicon drivers)
> ;echotail=64     ;echo cancel tail setting
> ;bridge=yes      ;native bridging (CAPI line interconnect) if available
> ;callgroup=1     ;Asterisk call group
> devices=2        ;number of concurrent calls on this controller
>                  ;(2 makes sense for single BRI, 30 for PRI)
> 
> thanks in advance,
> Andrea
> 
> Chi ricevesse questa mail per errore e' gentilmente pregato di cancellarla.
> 
> Visitate il sito http://www.frameweb.it
> 
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
> 
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>