[Asterisk-Users] TDM01B card configuration

[Mike Wissa]

The /var/log/messages lists:
kernel: Module 0: Not installed
kernel: Module 1: Not installed
kernel: Module 2: Not installed Jul  3 22:21:10 
kernel: Module 3: Installed -- AUTO FXO (FCC mode) 
kernel: Found a Wildcard TDM: Wildcard TDM400P REV I
(4 modules)

the ztcfg -vv:
Zaptel Configuration
======================


Channel map:

Channel 04: FXS Loopstart (Default) (Slaves: 04)

1 channels configured.

When you try to start asterisk. the following errors
appear

Jul  4 10:37:59 NOTICE[4015]: res_odbc.c:518
load_module: res_odbc loaded.
.........Jul  4 10:37:59 ERROR[4015]: chan_zap.c:6584
mkintf: Signalling requested on channel 4 is FXO
Loopstart but line is in FXS Loopstart signalling
Jul  4 10:37:59 ERROR[4015]: chan_zap.c:9927
setup_zap: Unable to register channel '4'
Jul  4 10:37:59 WARNING[4015]: loader.c:402
__load_resource: chan_zap.so: load_module failed,
returning -1
Jul  4 10:37:59 WARNING[4015]: loader.c:523
load_modules: Loading module chan_zap.so failed!

Any ideas?


--- Rich Adamson <radamson at routers.com> wrote:

> > I am trying the setup the TDM01B card. 1 FXO. I
> > connected it to a regular home line. in the
> > /etc/zaptel.conf, I have 
> > fxsls=4
> > In the /etc/asterisk/zapata.conf
> > I have:
> > signaling=fxs_ls
> > language=en
> > group=1
> > context=default
> > channel => 4
> > 
> > When I start asterisk, I get this error:
> > ERROR[10376]: chan_zap.c:6584 mkintf; Signaling
> > requested on channel 4 is FXO Loopstart but line
> is in
> > FXS Loopstart Signaling
> > 
> > chan_zap.c:9927 setup_zap: Unable to register
> channel
> > '4'
> > 
> > Maybe I have something misconfigured. However, I
> > triead all combinations and it doesn't seem to
> work. 
> > 
> > If I take away those lines. Asterisk comes up and
> in
> > zaptel show command, I see the TDM400P card.
> > Please help.
> > Thanks
> 
> What do you see listed in 'dmesg'? 
> 
> It should look something like:
> Module 0: Installed -- AUTO FXO (FCC mode)
> Module 1: Installed -- AUTO FXO (FCC mode)
> Module 2: Installed -- AUTO FXO (FCC mode)
> Module 3: Installed -- AUTO FXO (FCC mode)
> (The above example is from a TDM with four fxo
> modules installed.)
> 
> What do you see listed in 'ztcfg -vv'?
> 
> It should look something like:
> Channel 01: FXS Kewlstart (Default) (Slaves: 01)
> Channel 02: FXS Kewlstart (Default) (Slaves: 02)
> Channel 03: FXS Kewlstart (Default) (Slaves: 03)
> Channel 04: FXS Kewlstart (Default) (Slaves: 04)
> (Again, the above is from a TDM with four fxo
> modules, each configured
> for Kewlstart, not loopstart.)
> 
> If you're not seeing entries similar to the above,
> I'd have to guess
> that changes made to /etc/zaptel.conf and
> /etc/asterisk/zapata.conf
> are probably out of sync. (Meaning changes have been
> made to one or
> the other without restarting asterisk AND zaptel.)
> 
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
>
http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   
>
http://lists.digium.com/mailman/listinfo/asterisk-users
> 


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com