[asterisk-r2] FW: FW: te122p con E1 telecom conmutado

Moises Silva moises.silva at gmail.com
Fri Mar 5 16:12:03 CST 2010


El soporte oficial de R2 en Asterisk es OpenR2, por que insistes en usar
Unicall?

-- 
Moises Silva
Senior Software Engineer
Sangoma Technologies Inc. | 50 McIntosh Drive, Suite 120, Markham ON L3R 9T3
Canada
t. 1 905 474 1990 x 128 | e. moy at sangoma.com

On Fri, Mar 5, 2010 at 2:27 PM, omar ivan perez vargas
<o_i_p_v at hotmail.com>wrote:

>  Como estan bueno les cuento que hable con la gente de telecom y me
> digeron:
>
> Piloto primario: 5939260
> Tango MDE: 5939260 - 5939269
> Digitos q se envian son 7
>
> Señalizacion: MFC R2
> CRC: NO
>
> Se gun esto la variable protocolvariant=co-land,30,7,16
> como quedaria????? asi???
>
> y pues ya me entran llamadas y me salen llamadas pero se me corta en el
> primer timbre y me sale los siguientes errore por el cli
>
>
> Cuando entra una llamada sale:
>
> voip*CLI>
> MFC/R2 UniCall/1      <- 0001  [1/IDLE    /Idle          /Idle         ]
> MFC/R2 UniCall/1 Detected
> MFC/R2 UniCall/1 Creating a new call with CRN 32770
> MFC/R2 UniCall/1 1101  ->      [2/DETECTED/Seize ack     /Seize ack    ]
> [Mar  5 13:11:26] NOTICE[5365]: chan_unicall.c:2518 handle_uc_event:
> Unicall/1 event Detected
> MFC/R2 UniCall/1      <- 5 on  [2/DETECTED/Seize ack     /Seize ack    ]
> MFC/R2 UniCall/1 6 on  ->      [2/DETECTED/Group A       /Category req ]
> MFC/R2 UniCall/1      <- 5 off [2/DETECTED/Group A       /Category req ]
> MFC/R2 UniCall/1 Channel flush
> MFC/R2 UniCall/1 6 off ->      [2/DETECTED/Group A       /Category req ]
> MFC/R2 UniCall/1 R2 prot. err. [2/DETECTED/Group A       /Category req ]
> cause 32771 - T3 timed out
> MFC/R2 UniCall/1 1001  ->      [1/IDLE    /Idle          /Idle         ]
> [Mar  5 13:11:41] NOTICE[5365]: chan_unicall.c:2518 handle_uc_event:
> Unicall/1 event Protocol failure
> [Mar  5 13:11:41] ERROR[5365]: chan_unicall.c:2522 handle_uc_event:
> Unicall/1 protocol error. Cause 32771
> MFC/R2 UniCall/1 Channel echo cancel
> MFC/R2 UniCall/1      <- 1001  [1/IDLE    /Idle          /Idle         ]
> MFC/R2 UniCall/1 1001  ->      [1/IDLE    /Idle          /Idle         ]
> voip*CLI>
>
> y cuando trato de sacar llamada me sale:
>
> voip*CLI>
>     -- Executing [95101652 at L-DDN-DDI-CEL:1] Dial("SIP/100-c0001240",
> "Unicall/g1/5101652") in new stack
> MFC/R2 UniCall/1 Call control(1)
> MFC/R2 UniCall/1 Make call
> MFC/R2 UniCall/1 Creating a new call with CRN 32769
> MFC/R2 UniCall/1 0001  ->      [1/DIALING /Seize         /Idle         ]
>     -- Called g1/5101652
> [Mar  5 13:10:31] NOTICE[5371]: chan_unicall.c:2518 handle_uc_event:
> Unicall/1 event Dialing
> [Mar  5 13:10:31] NOTICE[5371]: chan_unicall.c:1914 unicall_exception:
> Exception on 25, channel 1
> MFC/R2 UniCall/1      <- 1101  [1/DIALING /Seize         /Idle         ]
> MFC/R2 UniCall/1 5 on  ->      [2/DIALING /Group I       /DNIS         ]
> MFC/R2 UniCall/1      <- 1 on  [2/DIALING /Group I       /DNIS         ]
> MFC/R2 UniCall/1 Channel flush
> MFC/R2 UniCall/1 5 off ->      [2/DIALING /Group I       /DNIS         ]
> MFC/R2 UniCall/1      <- 1 off [2/DIALING /Group I       /DNIS         ]
> MFC/R2 UniCall/1 1 on  ->      [2/DIALING /Group I       /DNIS         ]
> MFC/R2 UniCall/1      <- 1 on  [2/DIALING /Group I       /DNIS         ]
> MFC/R2 UniCall/1 Channel flush
> MFC/R2 UniCall/1 1 off ->      [2/DIALING /Group I       /DNIS         ]
> MFC/R2 UniCall/1      <- 1 off [2/DIALING /Group I       /DNIS         ]
> MFC/R2 UniCall/1 0 on  ->      [2/DIALING /Group I       /DNIS         ]
> MFC/R2 UniCall/1      <- 5 on  [2/DIALING /Group I       /DNIS         ]
> MFC/R2 UniCall/1 Channel flush
> MFC/R2 UniCall/1 0 off ->      [2/DIALING /Group I       /DNIS         ]
> MFC/R2 UniCall/1      <- 5 off [2/DIALING /Group I       /DNIS         ]
> MFC/R2 UniCall/1 R2 prot. err. [2/DIALING /Group I       /DNIS         ]
> cause 32772 - Unexpected MF6 signal
> MFC/R2 UniCall/1 1001  ->      [1/IDLE    /Idle          /Idle         ]
> [Mar  5 13:10:31] NOTICE[5371]: chan_unicall.c:2518 handle_uc_event:
> Unicall/1 event Protocol failure
> [Mar  5 13:10:31] ERROR[5371]: chan_unicall.c:2522 handle_uc_event:
> Unicall/1 protocol error. Cause 32772
> MFC/R2 UniCall/1 Channel echo cancel
> MFC/R2 UniCall/1 Channel gains
> MFC/R2 UniCall/1 Channel switching
>     -- Hungup 'UniCall/1-1'
>   == Everyone is busy/congested at this time (1:0/0/1)
>     -- Executing [95101652 at L-DDN-DDI-CEL:2] Hangup("SIP/100-c0001240", "")
> in new stack
>   == Spawn extension (L-DDN-DDI-CEL, 95101652, 2) exited non-zero on
> 'SIP/100-c0001240'
> MFC/R2 UniCall/1      <- 1001  [1/IDLE    /Idle          /Idle         ]
> MFC/R2 UniCall/1 1001  ->      [1/IDLE    /Idle          /Idle         ]
> voip*CLI>
>
> que sera?
>
> op
>
> ------------------------------
> From: o_i_p_v at hotmail.com
> To: asterisk-r2 at lists.digium.com
> Subject: FW: [asterisk-r2] FW: te122p con E1 telecom conmutado
> Date: Fri, 5 Mar 2010 13:08:17 -0500
>
> y cuando trato de marcar por el canal me sale:
>
> voip*CLI>
>     -- Executing [95101652 at L-DDN-DDI-CEL:1] Dial("SIP/100-c4003530",
> "Unicall/g1/5101652") in new stack
> [Mar  5 13:07:17] WARNING[4661]: app_dial.c:1183 dial_exec_full: Unable to
> create channel of type 'Unicall' (cause 0 - Unknown)
>   == Everyone is busy/congested at this time (1:0/0/1)
>     -- Executing [95101652 at L-DDN-DDI-CEL:2] Hangup("SIP/100-c4003530", "")
> in new stack
>   == Spawn extension (L-DDN-DDI-CEL, 95101652, 2) exited non-zero on
> 'SIP/100-c4003530'
> voip*CLI>
>
>
> Op
>
> ------------------------------
> From: o_i_p_v at hotmail.com
> To: asterisk-r2 at lists.digium.com
> Date: Fri, 5 Mar 2010 13:06:11 -0500
> Subject: [asterisk-r2] FW: te122p con E1 telecom conmutado
>
>
> Hola
>
> Bueno les cuento que en el balun conecte al contrario el rx y el tx y la
> tarjeta se coloco en verde...
>
> ahora me salen:
>
> [Mar  5 13:03:08] ERROR[4529]: chan_unicall.c:2522 handle_uc_event:
> Unicall/28 protocol error. Cause 32773
> MFC/R2 UniCall/29      <- 0100  [1/BLOCKED /Idle          /Idle         ]
> MFC/R2 UniCall/29 R2 prot. err. [1/BLOCKED /Idle          /Idle         ]
> cause 32773 - Unexpected CAS bit pattern
> MFC/R2 UniCall/29 1001  ->      [1/BLOCKED /Idle          /Idle         ]
>
>
> que significa esto???
>
> gracias
>
> Omar
>
> ------------------------------
> From: o_i_p_v at hotmail.com
> To: asterisk-r2 at lists.digium.com
> Subject: FW: [asterisk-r2] te122p con E1 telecom conmutado
> Date: Fri, 5 Mar 2010 12:27:06 -0500
>
> Mi configuracion
>
> ------------------------------
> From: o_i_p_v at hotmail.com
> To: asterisk-r2 at lists.digium.com
> Subject: FW: [asterisk-r2] te122p con E1 telecom conmutado
> Date: Fri, 5 Mar 2010 11:47:55 -0500
>
> Pues le cuento:
> El canal esta actualmente conectado a una planta Alcatel OmniPCX y esta
> funcionando
> el cable UTP sale del balun y entra al puerto de la Alcatel donde dice PBX
> ese mismo cable es el que uso para conectar a mi tarjeta
> Mi configuracion es:
>
> zaptel.conf
>
> # Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER)
> span=1,1,0,cas,hdb3
> # termtype: te
> cas=1-15:1101
> #dchan=16
> cas=17-31:1101
> # Span 2: WCTDM/0 "Wildcard AEX410 Board 1"
> fxsks=32
> fxsks=33
> fxsks=34
> fxsks=35
> # Global data
> loadzone        = us
> defaultzone     = us
>
>
> unicall.conf
>
> [channels]
> language=es
> usecallerid=yes
> hidecallerid=no
> callwaitingcallerid=yes
> threewaycalling=yes
> transfer=yes
> cancallforward=yes
> callreturn=yes
> echocancel=yes
> echocancelwhenbridged=yes
> echotraining=yes
> rxgain=0.0
> txgain=0.0
> group=1
> callgroup=1
> pickupgroup=1
> immediate=no
> musiconhold=default
> protocolclass=mfcr2
> ; protocolvariant=co-land,30,1,16
> protocolvariant=co-land,30,7,16
> protocolend=cpe
> group = 1
> loglevel = 255
> context= from-pstn
> channel => 1-15
> channel => 17-31
> ;skip time slot 16
>
>
> extensions.conf
>
> [from-pstn]
> exten=>_.,1,Answer()
> exten=>_.,n,Goto(ivr,s,1)
> exten=>_.,n,Hangup
>
> exten=>9260,1,Answer()
> exten=>9260,n,Goto(ivr,s,1)
> exten=>9260,n,Hangup
>
> Tengo entendido q en el zapata.conf no se coloca nada del E1 pero aca les
> mando:
>
> [trunkgroups]
> [channels]
> language=es
> usecallerid=yes
> hidecallerid=no
> callwaiting=yes
> usecallingpres=yes
> callwaitingcallerid=yes
> threewaycalling=yes
> transfer=yes
> canpark=yes
> cancallforward=yes
> callreturn=yes
> echocancel=yes
> echocancelwhenbridged=yes
> relaxdtmf=yes
> rxgain=0.0
> txgain=0.0
> callgroup=1
> pickupgroup=1
> immediate=no
> faxdetect=incoming
> busydetect=yes
> busycount=4
>
> ; Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER)
> ;group=1
> ;context=from-pstn
> ;switchtype = euroisdn
> ;signalling = pri_cpe
> ;channel => 1-31
> ; Span 2: WCTDM/0 "Wildcard AEX410 Board 1"
> ;;; line="32 WCTDM/0/0 RED"
> signalling=fxs_ks
> callerid=asreceived
> group=2
> context=from-pstn
> channel => 32
> ;;; line="33 WCTDM/0/1 RED"
> signalling=fxs_ks
> callerid=asreceived
> group=2
> context=from-pstn
> channel => 33
> ;;; line="34 WCTDM/0/2 RED"
> signalling=fxs_ks
> callerid=asreceived
> group=2
> context=from-pstn
> channel => 34
> ;;; line="35 WCTDM/0/3 RED"
> signalling=fxs_ks
> callerid=asreceived
> group=2
> context=from-pstn
> channel => 35
>
> gracias
> <http://search.msn.com/results.aspx?q=windows+vista&mkt=en-US&form=QBRE>
> ------------------------------
> Connect to the next generation of MSN Messenger  Get it now!
> <http://imagine-msn.com/messenger/launch80/default.aspx?locale=en-us&source=wlmailtagline>
>
> --
> _____________________________________________________________________
> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>
> asterisk-r2 mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-r2
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-r2/attachments/20100305/ddd296c6/attachment.htm 


More information about the asterisk-r2 mailing list