[asterisk-r2] FW: FW: te122p con E1 telecom conmutado

omar ivan perez vargas o_i_p_v at hotmail.com
Fri Mar 5 16:15:22 CST 2010


aaa bueno porque fue la primera opción q encontré....
pero si tu me recmiendas que pruebe con OpenR2 y que me ira mejor ...
pues le hago

gracias,

Omar

Date: Fri, 5 Mar 2010 17:12:03 -0500
From: moises.silva at gmail.com
To: asterisk-r2 at lists.digium.com
Subject: Re: [asterisk-r2] FW: FW: te122p con E1 telecom conmutado

El soporte oficial de R2 en Asterisk es OpenR2, por que insistes en usar Unicall?

-- 
Moises Silva
Senior Software Engineer
Sangoma Technologies Inc. | 50 McIntosh Drive, Suite 120, Markham ON L3R 9T3 Canada

t. 1 905 474 1990 x 128 | e. moy at sangoma.com

On Fri, Mar 5, 2010 at 2:27 PM, omar ivan perez vargas <o_i_p_v at hotmail.com> wrote:






Como estan bueno les cuento que hable con la gente de telecom y me digeron:

Piloto primario: 5939260
Tango MDE: 5939260 - 5939269
Digitos q se envian son 7

Señalizacion: MFC R2
CRC: NO

Se gun esto la variable protocolvariant=co-land,30,7,16

como quedaria????? asi???

y pues ya me entran llamadas y me salen llamadas pero se me corta en el primer timbre y me sale los siguientes errore por el cli

Cuando entra una llamada sale:

 


voip*CLI>
MFC/R2 UniCall/1      <- 0001  [1/IDLE    /Idle          /Idle         ]
MFC/R2 UniCall/1 Detected
MFC/R2 UniCall/1 Creating a new call with CRN 32770
MFC/R2 UniCall/1 1101  ->      [2/DETECTED/Seize ack     /Seize ack    ]

[Mar  5 13:11:26] NOTICE[5365]: chan_unicall.c:2518 handle_uc_event: Unicall/1 event Detected
MFC/R2 UniCall/1      <- 5 on  [2/DETECTED/Seize ack     /Seize ack    ]
MFC/R2 UniCall/1 6 on  ->      [2/DETECTED/Group A       /Category req ]

MFC/R2 UniCall/1      <- 5 off [2/DETECTED/Group A       /Category req ]
MFC/R2 UniCall/1 Channel flush
MFC/R2 UniCall/1 6 off ->      [2/DETECTED/Group A       /Category req ]
MFC/R2 UniCall/1 R2 prot. err. [2/DETECTED/Group A       /Category req ] cause 32771 - T3 timed out

MFC/R2 UniCall/1 1001  ->      [1/IDLE    /Idle          /Idle         ]
[Mar  5 13:11:41] NOTICE[5365]: chan_unicall.c:2518 handle_uc_event: Unicall/1 event Protocol failure
[Mar  5 13:11:41] ERROR[5365]: chan_unicall.c:2522 handle_uc_event: Unicall/1 protocol error. Cause 32771

MFC/R2 UniCall/1 Channel echo cancel
MFC/R2 UniCall/1      <- 1001  [1/IDLE    /Idle          /Idle         ]
MFC/R2 UniCall/1 1001  ->      [1/IDLE    /Idle          /Idle         ]
voip*CLI>
 

y cuando trato de sacar llamada me sale:

 
voip*CLI>
    -- Executing [95101652 at L-DDN-DDI-CEL:1] Dial("SIP/100-c0001240", "Unicall/g1/5101652") in new stack
MFC/R2 UniCall/1 Call control(1)
MFC/R2 UniCall/1 Make call
MFC/R2 UniCall/1 Creating a new call with CRN 32769

MFC/R2 UniCall/1 0001  ->      [1/DIALING /Seize         /Idle         ]
    -- Called g1/5101652
[Mar  5 13:10:31] NOTICE[5371]: chan_unicall.c:2518 handle_uc_event: Unicall/1 event Dialing
[Mar  5 13:10:31] NOTICE[5371]: chan_unicall.c:1914 unicall_exception: Exception on 25, channel 1

MFC/R2 UniCall/1      <- 1101  [1/DIALING /Seize         /Idle         ]
MFC/R2 UniCall/1 5 on  ->      [2/DIALING /Group I       /DNIS         ]
MFC/R2 UniCall/1      <- 1 on  [2/DIALING /Group I       /DNIS         ]

MFC/R2 UniCall/1 Channel flush
MFC/R2 UniCall/1 5 off ->      [2/DIALING /Group I       /DNIS         ]
MFC/R2 UniCall/1      <- 1 off [2/DIALING /Group I       /DNIS         ]
MFC/R2 UniCall/1 1 on  ->      [2/DIALING /Group I       /DNIS         ]

MFC/R2 UniCall/1      <- 1 on  [2/DIALING /Group I       /DNIS         ]
MFC/R2 UniCall/1 Channel flush
MFC/R2 UniCall/1 1 off ->      [2/DIALING /Group I       /DNIS         ]
MFC/R2 UniCall/1      <- 1 off [2/DIALING /Group I       /DNIS         ]

MFC/R2 UniCall/1 0 on  ->      [2/DIALING /Group I       /DNIS         ]
MFC/R2 UniCall/1      <- 5 on  [2/DIALING /Group I       /DNIS         ]
MFC/R2 UniCall/1 Channel flush
MFC/R2 UniCall/1 0 off ->      [2/DIALING /Group I       /DNIS         ]

MFC/R2 UniCall/1      <- 5 off [2/DIALING /Group I       /DNIS         ]
MFC/R2 UniCall/1 R2 prot. err. [2/DIALING /Group I       /DNIS         ] cause 32772 - Unexpected MF6 signal
MFC/R2 UniCall/1 1001  ->      [1/IDLE    /Idle          /Idle         ]

[Mar  5 13:10:31] NOTICE[5371]: chan_unicall.c:2518 handle_uc_event: Unicall/1 event Protocol failure
[Mar  5 13:10:31] ERROR[5371]: chan_unicall.c:2522 handle_uc_event: Unicall/1 protocol error. Cause 32772
MFC/R2 UniCall/1 Channel echo cancel

MFC/R2 UniCall/1 Channel gains
MFC/R2 UniCall/1 Channel switching
    -- Hungup 'UniCall/1-1'
  == Everyone is busy/congested at this time (1:0/0/1)
    -- Executing [95101652 at L-DDN-DDI-CEL:2] Hangup("SIP/100-c0001240", "") in new stack

  == Spawn extension (L-DDN-DDI-CEL, 95101652, 2) exited non-zero on 'SIP/100-c0001240'
MFC/R2 UniCall/1      <- 1001  [1/IDLE    /Idle          /Idle         ]
MFC/R2 UniCall/1 1001  ->      [1/IDLE    /Idle          /Idle         ]

voip*CLI>
 

que sera?

 

op
 



From: o_i_p_v at hotmail.com
To: asterisk-r2 at lists.digium.com
Subject: FW: [asterisk-r2] FW: te122p con E1 telecom conmutado

Date: Fri, 5 Mar 2010 13:08:17 -0500



y cuando trato de marcar por el canal me sale:
 
voip*CLI>
    -- Executing [95101652 at L-DDN-DDI-CEL:1] Dial("SIP/100-c4003530", "Unicall/g1/5101652") in new stack
[Mar  5 13:07:17] WARNING[4661]: app_dial.c:1183 dial_exec_full: Unable to create channel of type 'Unicall' (cause 0 - Unknown)

  == Everyone is busy/congested at this time (1:0/0/1)
    -- Executing [95101652 at L-DDN-DDI-CEL:2] Hangup("SIP/100-c4003530", "") in new stack
  == Spawn extension (L-DDN-DDI-CEL, 95101652, 2) exited non-zero on 'SIP/100-c4003530'

voip*CLI>

 
Op
 


From: o_i_p_v at hotmail.com
To: asterisk-r2 at lists.digium.com
Date: Fri, 5 Mar 2010 13:06:11 -0500

Subject: [asterisk-r2] FW: te122p con E1 telecom conmutado



Hola
 
Bueno les cuento que en el balun conecte al contrario el rx y el tx y la tarjeta se coloco en verde...
 
ahora me salen:
 
[Mar  5 13:03:08] ERROR[4529]: chan_unicall.c:2522 handle_uc_event: Unicall/28 protocol error. Cause 32773

MFC/R2 UniCall/29      <- 0100  [1/BLOCKED /Idle          /Idle         ]
MFC/R2 UniCall/29 R2 prot. err. [1/BLOCKED /Idle          /Idle         ] cause 32773 - Unexpected CAS bit pattern
MFC/R2 UniCall/29 1001  ->      [1/BLOCKED /Idle          /Idle         ]


 
que significa esto???
 
gracias
 
Omar
 


From: o_i_p_v at hotmail.com
To: asterisk-r2 at lists.digium.com
Subject: FW: [asterisk-r2] te122p con E1 telecom conmutado

Date: Fri, 5 Mar 2010 12:27:06 -0500



Mi configuracion
 


From: o_i_p_v at hotmail.com
To: asterisk-r2 at lists.digium.com
Subject: FW: [asterisk-r2] te122p con E1 telecom conmutado

Date: Fri, 5 Mar 2010 11:47:55 -0500





Pues le cuento:
El canal esta actualmente conectado a una planta Alcatel OmniPCX y esta funcionando
el cable UTP sale del balun y entra al puerto de la Alcatel donde dice PBX
ese mismo cable es el que uso para conectar a mi tarjeta

Mi configuracion es:
 
zaptel.conf
 
# Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER)
span=1,1,0,cas,hdb3
# termtype: te
cas=1-15:1101
#dchan=16
cas=17-31:1101
# Span 2: WCTDM/0 "Wildcard AEX410 Board 1"

fxsks=32
fxsks=33
fxsks=34
fxsks=35
# Global data
loadzone        = us
defaultzone     = us

 
unicall.conf
 
[channels]
language=es
usecallerid=yes
hidecallerid=no
callwaitingcallerid=yes

threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
echotraining=yes
rxgain=0.0
txgain=0.0
group=1
callgroup=1
pickupgroup=1
immediate=no

musiconhold=default
protocolclass=mfcr2
; protocolvariant=co-land,30,1,16
protocolvariant=co-land,30,7,16
protocolend=cpe
group = 1
loglevel = 255
context= from-pstn
channel => 1-15
channel => 17-31

;skip time slot 16

 
extensions.conf
 
[from-pstn]
exten=>_.,1,Answer()
exten=>_.,n,Goto(ivr,s,1)
exten=>_.,n,Hangup
 
exten=>9260,1,Answer()
exten=>9260,n,Goto(ivr,s,1)

exten=>9260,n,Hangup

Tengo entendido q en el zapata.conf no se coloca nada del E1 pero aca les mando:
 
[trunkgroups]
[channels]
language=es
usecallerid=yes
hidecallerid=no
callwaiting=yes

usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
relaxdtmf=yes
rxgain=0.0

txgain=0.0
callgroup=1
pickupgroup=1
immediate=no
faxdetect=incoming
busydetect=yes
busycount=4

; Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER)
;group=1
;context=from-pstn
;switchtype = euroisdn

;signalling = pri_cpe
;channel => 1-31
; Span 2: WCTDM/0 "Wildcard AEX410 Board 1"
;;; line="32 WCTDM/0/0 RED"
signalling=fxs_ks
callerid=asreceived
group=2
context=from-pstn

channel => 32
;;; line="33 WCTDM/0/1 RED"
signalling=fxs_ks
callerid=asreceived
group=2
context=from-pstn
channel => 33
;;; line="34 WCTDM/0/2 RED"
signalling=fxs_ks
callerid=asreceived

group=2
context=from-pstn
channel => 34
;;; line="35 WCTDM/0/3 RED"
signalling=fxs_ks
callerid=asreceived
group=2
context=from-pstn
channel => 35

gracias
 		 	   		  

Connect to the next generation of MSN Messenger   Get it now! 


--

_____________________________________________________________________

-- Bandwidth and Colocation Provided by http://www.api-digital.com --



asterisk-r2 mailing list

To UNSUBSCRIBE or update options visit:

   http://lists.digium.com/mailman/listinfo/asterisk-r2


 		 	   		  
_________________________________________________________________
Discover the new Windows Vista
http://search.msn.com/results.aspx?q=windows+vista&mkt=en-US&form=QBRE
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-r2/attachments/20100305/6b133fbb/attachment-0001.htm 


More information about the asterisk-r2 mailing list