[Asterisk-Dev] Asterisk + Fritz!PCI + CAPI

[Ronan GUILLOU]

Thanks Lawrence for your prompt answer,
I have perhaps to read the doc too :), but which documentation are you
talking about ?

By the way : 
- I also use chan_capi 0.3.1.
- My ISDN access is provided by my telco France Telecom

-My capi.conf file is : 
;====================================================
[general]
nationalprefix=0
internationalprefix=00
rxgain=0.8
txgain=0.8

[interfaces]
msn=0492919500
incomingmsn=*
controller=1
softdtmf=1
accountcode=
context=from_capi_1
;echosquelch=1
;echocancel=yes
;echotail=64
callgroup=1
deflect=12345678
devices=2
;====================================================

/Ronan

On Thu, 2004-04-15 at 14:38, Conroy, Lawrence (SMTP) wrote:
> Hi Ronan, folks,
>    The Fritz card works for me with RH9 and chan_capi 031.
> It has proved to be a *great deal* more rock solid than others;
> (for analogue lines the S100/WC101, or even the Linejack).
> 
> The ONLY issue I have is that I don't get ringing dialback so
> calling out gives a silence until the other party picks up
> (plus the recent changes to locks in * required a tweak to the
>   chan_capi source to match).
> 
> You have set your config up to support more than one B channel, I hope?
> If only one number is always used to dial out, then this might be a 
> problem
> (it was for me until I actually read the documentation and set it right 
> :).
> 
> You don't say what your ISDN connection is; it seems that some ISDN 
> PBXes
> take a considerable time to clear the remote call and will not respond
> correctly to a new call request until this is done.
> 
> In short, the Fritz card, RH9, chan_capi 031, and a recent * CVS load
> works fine here (running on an Old Dell - 450 MHz PIII with 256 MB RAM).
> 
> I'm currently connected to a Siemens HiPath ISPBX, but have also tried
> a British Telecom BRI line; all work.
> 
> all the best,
>    Lawrence
> 
> On 15 Apr 2004, at 1:11 pm, Ronan GUILLOU wrote:
> 
> > I'm currently testing the setup Asterisk+CAPI+AVM Fritz!PCI v2.0 -
> > Single span BRI-ISDN-S/T card" on a Linux RedHat 9.
> >
> > After a successful install, I have done some successfull outgoing and
> > incoming calls.
> >
> > Digging a little bit more, I have nevertheless observed some issues  :
> >         -1) sometimes "chan_capi" module fails to write in the pipe
> >         and I get the following error :
> >           chan_capi.c pipe_frame : wrote -1 bytes instead of 40
> >
> >         -2) chan_capi.c
> >         when I repeat the following operation several times
> >                 - making an outgoing call to the PSTN
> >                 - the remote phone starts ringing
> >                 - I hangup locally
> >                 - the remote phone stops ringing
> >         I sometimes the call fails with the following error :
> >           "capi_request : didn't find device with
> > outgoing                       msn=0492919590.
> > you should check your config"
> >         I sounds like all the call context are still busy and not
> > released
> > immidiately after the hangup. Then i waiting a few seconds, i am able
> > again to make outgoing calls.
> >
> > Has anyone tested a releable BRI hardware for asterisk ?
> >
> > _______________________________________________
> > Asterisk-Dev mailing list
> > Asterisk-Dev at lists.digium.com
> > http://lists.digium.com/mailman/listinfo/asterisk-dev
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-dev
> >