[Asterisk-bsd] E1 PRI error: "!! Got I-frame while link state 2" and "!! Got a UA, but i'm in state 1" (long)

[Dinesh Nair]

On 10/21/05 01:14 Konstantin Prokazoff said the following:
>     We haven't touched drivers yet, but I think card you have using aren't
> buggy. Can you try to set in zaptel.conf different sync sources for
> different spans? For example, first span, sync source 1, fourth span - sync

i have, first setting all spans to use timing=0, then using your suggestion 
above. neither worked. see my other email on this to asterisk-users.

> source 2 and so on. Don't use CRC if this options not required by other
> side, cause due to standards, CRC4 not recommended for E1s. As addition, can

removed CRC4.

> And very interesting for me, what type of chipset are you using. I have 4
> severs on Intel 72 and 73 chipset, but zttest shows no more than 99,98%.

zttest
--- Results after 21 passes ---
Best: 100.000000 -- Worst: 99.987793 -- Average: 99.998256

on other runs, i've got averages of 99.9998 as well.

dmesg follows:

Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
         The Regents of the University of California. All rights reserved.
FreeBSD 4.11-STABLE #0: Wed Oct 19 19:49:04 MYT 2005
     dinesh at prophet.alphaque.com:/usr/src/sys/compile/ALPHAQUE
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 2791123856 Hz
CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2791.12-MHz 686-class CPU)
   Origin = "GenuineIntel"  Id = 0xf25  Stepping = 5
 
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C
MOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
   Hyperthreading: 2 logical CPUs
real memory  = 1073676288 (1048512K bytes)
avail memory = 1014792192 (991008K bytes)
Preloaded elf kernel "kernel" at 0xc1d12000.
Preloaded mfs_root "/mfsroot" at 0xc1d1209c.
Warning: Pentium 4 CPU: PSE disabled
Pentium Pro MTRR support enabled
md0: Preloaded image </mfsroot> 25165824 bytes at 0xc0510aac
md1: Malloc disk
Using $PIR table, 10 entries at 0xc00fdf20
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
pci0: <PCI bus> on pcib0
pci0: <ATI Mach64-GR graphics accelerator> at 5.0 irq 10
atapci0: <ITE 8211F/8212F PCI Controller> port 
0x1400-0x140f,0x1420-0x1423,0x142
8-0x142f,0x1424-0x1427,0x1430-0x1437 irq 5 at device 6.0 on pci0
ata2: at 0x1430 on atapci0
ata3: at 0x1428 on atapci0
isab0: <PCI to ISA bridge (vendor=1166 device=0203)> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <ServerWorks CSB6 ATA100 controller (channel 0+1)> port 
0x1410-0x141f,0
x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci1
ata1: at 0x170 irq 15 on atapci1
ohci0: <OHCI (generic) USB controller> mem 0xcc000-0xccfff irq 9 at device 
15.2

usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: 4 ports with 4 removable, self powered
pcib1: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x10ee, dev=0x0314) at 5.0 irq 7
pcib2: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib2
bge0: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2002> mem 
0xfc700000
-0xfc70ffff,0xfc710000-0xfc71ffff irq 11 at device 0.0 on pci2
bge0: Ethernet address: 00:0d:61:15:6d:da
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 
1000baseTX
-FDX, auto
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2002> mem 
0xfc720000
-0xfc72ffff,0xfc730000-0xfc73ffff irq 10 at device 0.1 on pci2
bge1: Ethernet address: 00:0d:61:15:6d:db
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseTX PHY> on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 
1000baseTX
-FDX, auto
pcib3: <Host to PCI bridge> on motherboard
pci3: <PCI bus> on pcib3
pcib4: <Host to PCI bridge> on motherboard
pci4: <PCI bus> on pcib4
orm0: <Option ROMs> at iomem 
0xc0000-0xc7fff,0xc8000-0xcbfff,0xdf000-0xdffff on
isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
BRIDGE 020214 loaded
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.35 initialized.  Default = block all, Logging = enabled
ad4: 76319MB <ST380011A> [155061/16/63] at ata2-master UDMA100
acd0: CDROM <QSI CD-ROM SCR-242> at ata0-master PIO4
Mounting root from ufs:/dev/md0c

-- 
Regards,                           /\_/\   "All dogs go to heaven."
dinesh at alphaque.com                (0 0)    http://www.alphaque.com/
+==========================----oOO--(_)--OOo----==========================+
| for a in past present future; do                                        |
|   for b in clients employers associates relatives neighbours pets; do   |
|   echo "The opinions here in no way reflect the opinions of my $a $b."  |
| done; done                                                              |
+=========================================================================+