[asterisk-users] AsteriskNOW with AX1600P card

[Fernando Pizarro]

El 27/01/14 13:44, Fernando Pizarro escribió:
> El 27/01/14 13:26, A J Stiles escribió:
>> On Monday 27 January 2014, Fernando Pizarro wrote:
>>> Hi all!
>>>
>>> I'm new with telephony cards and DAHDI drivers. I have installed
>>> Asterisk NOW 3.0.0 and update to Asterisk 11.7.0, modules are update
>>> too.
>>>
>>> I'm following the installation guide of Atcom [1] for AX1600P analogic
>>> card, modules are loaded
>>>
>>> [root at pbx ~]# lsmod | grep -E "hisax|netjet|dahdi"
>>> netjet                 14618  0
>>> isdnhdlc                4523  1 netjet
>>> mISDNipac              33989  1 netjet
>>> mISDN_core             73118  3 netjet,mISDNipac
>>> hisax                 410162  0
>>> isdn                  119265  1 hisax
>>> dahdi_transcode         5240  1 wctc4xxp
>>> dahdi_voicebus         49368  2 wctdm24xxp,wcte12xp
>>> dahdi                 207790  15
>>> xpp,dahdi_transcode,wcb4xxp,wctdm,wcfxo,wcaxx,wctdm24xxp,wcte11xp,wct1xxp,w
>>>
>>> cte13xp,wcte12xp,dahdi_voicebus,wcte43x,wct4xxp,oct612x crc_ccitt
>>>      1369  4 isdnhdlc,hisax,wctdm24xxp,dahdi
>>>
>>> and there is the output of lspci command:
>>>
>>> [root at pbx ~]# lspci -vvvvvv -s 02:03.0
>>> 02:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
>>> Modem/ISDN interface
>>>           Subsystem: Device b300:0003
>>>           Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>>> ParErr- Stepping- SERR- FastB2B- DisINTx-
>>>           Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>>>
>>>   >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>>>
>>>           Latency: 32 (250ns min, 32000ns max)
>>>           Interrupt: pin A routed to IRQ 12
>>>           Region 0: I/O ports at a000 [size=256]
>>>           Region 1: Memory at fb001000 (32-bit, non-prefetchable)
>>> [size=4K]
>>>           Capabilities: [40] Power Management version 2
>>>                   Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA
>>> PME(D0+,D1-,D2+,D3hot+,D3cold+)
>>>                   Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>>>           Kernel modules: hisax, netjet
>>>
>>> When I run dahdi_genconf I get the following error:
>>>
>>> [root at pbx ~]# dahdi_genconf
>>> Empty configuration -- no spans
>>> /usr/sbin/dahdi_span_types: línea 158: cd:
>>> /sys/bus/dahdi_devices/devices/*: No existe el fichero o el directorio
>>> cat: /sys/bus/dahdi_devices/devices/*/location: No existe el fichero o
>>> el directorio
>>> cat: /sys/bus/dahdi_devices/devices/*/hardware_id: No existe el fichero
>>> o el directorio
>>> cat: /sys/bus/dahdi_devices/devices/*/spantype: No existe el fichero o
>>> el directorio
>>> Empty configuration -- no spans
>>> /usr/sbin/dahdi_span_assignments: línea 183: cd:
>>> /sys/bus/dahdi_devices/devices/*: No existe el fichero o el directorio
>>> cut: /sys/bus/dahdi_devices/devices/*/spantype: No existe el fichero o
>>> el directorio
>>> Empty configuration -- no spans
>>> Empty configuration -- no spans
>>>
>>> Which is the better way to install Asterisk NOW? I need install with AX
>>> card inserted before?
>>
>> That looks like the result of a part-finished upgrade.
>>
>> You probably need to rebuild DAHDI *while the card is installed in the
>> machine*, so it can detect the hardware properly; and then after doing
>> that,
>> you may need to rebuild Asterisk again.
>>
>
> Hi,
>
> I'm going to try reinstall with card installed.
>
> Regards.
> Fernando.

Hi again!

I'm tried reinstall with card installed but I get the same error when I 
run dahdi_genconf. I noticed the leds are on now and dahdi_scan doesn't 
show anything while before it print 99.97% 99.95%... continuously.

How I can obtain more information? some command? debugging options?

Thanks a lot. Regards.
Fernando.