[asterisk-users] AsteriskNOW with AX1600P card

[Fernando Pizarro]

El 27/01/14 13:26, A J Stiles escribió:
> On Monday 27 January 2014, Fernando Pizarro wrote:
>> Hi all!
>>
>> I'm new with telephony cards and DAHDI drivers. I have installed
>> Asterisk NOW 3.0.0 and update to Asterisk 11.7.0, modules are update too.
>>
>> I'm following the installation guide of Atcom [1] for AX1600P analogic
>> card, modules are loaded
>>
>> [root at pbx ~]# lsmod | grep -E "hisax|netjet|dahdi"
>> netjet                 14618  0
>> isdnhdlc                4523  1 netjet
>> mISDNipac              33989  1 netjet
>> mISDN_core             73118  3 netjet,mISDNipac
>> hisax                 410162  0
>> isdn                  119265  1 hisax
>> dahdi_transcode         5240  1 wctc4xxp
>> dahdi_voicebus         49368  2 wctdm24xxp,wcte12xp
>> dahdi                 207790  15
>> xpp,dahdi_transcode,wcb4xxp,wctdm,wcfxo,wcaxx,wctdm24xxp,wcte11xp,wct1xxp,w
>> cte13xp,wcte12xp,dahdi_voicebus,wcte43x,wct4xxp,oct612x crc_ccitt
>>      1369  4 isdnhdlc,hisax,wctdm24xxp,dahdi
>>
>> and there is the output of lspci command:
>>
>> [root at pbx ~]# lspci -vvvvvv -s 02:03.0
>> 02:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
>> Modem/ISDN interface
>>           Subsystem: Device b300:0003
>>           Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B- DisINTx-
>>           Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>>
>>   >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>>
>>           Latency: 32 (250ns min, 32000ns max)
>>           Interrupt: pin A routed to IRQ 12
>>           Region 0: I/O ports at a000 [size=256]
>>           Region 1: Memory at fb001000 (32-bit, non-prefetchable) [size=4K]
>>           Capabilities: [40] Power Management version 2
>>                   Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA
>> PME(D0+,D1-,D2+,D3hot+,D3cold+)
>>                   Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>>           Kernel modules: hisax, netjet
>>
>> When I run dahdi_genconf I get the following error:
>>
>> [root at pbx ~]# dahdi_genconf
>> Empty configuration -- no spans
>> /usr/sbin/dahdi_span_types: línea 158: cd:
>> /sys/bus/dahdi_devices/devices/*: No existe el fichero o el directorio
>> cat: /sys/bus/dahdi_devices/devices/*/location: No existe el fichero o
>> el directorio
>> cat: /sys/bus/dahdi_devices/devices/*/hardware_id: No existe el fichero
>> o el directorio
>> cat: /sys/bus/dahdi_devices/devices/*/spantype: No existe el fichero o
>> el directorio
>> Empty configuration -- no spans
>> /usr/sbin/dahdi_span_assignments: línea 183: cd:
>> /sys/bus/dahdi_devices/devices/*: No existe el fichero o el directorio
>> cut: /sys/bus/dahdi_devices/devices/*/spantype: No existe el fichero o
>> el directorio
>> Empty configuration -- no spans
>> Empty configuration -- no spans
>>
>> Which is the better way to install Asterisk NOW? I need install with AX
>> card inserted before?
>
> That looks like the result of a part-finished upgrade.
>
> You probably need to rebuild DAHDI *while the card is installed in the
> machine*, so it can detect the hardware properly; and then after doing that,
> you may need to rebuild Asterisk again.
>

Hi,

I'm going to try reinstall with card installed.

Regards.
Fernando.