[asterisk-users] [asterik-users] Installing PRI card

[NaJIm]

Hi,

As Eric mentioned I made my zapata.conf and zaptel.conf to match each
other.

My *zapata.conf *was

*group=1*
*switchtype=euroisdn*
*signalling=pri_cpe*
*callerid=asreceived*
*usecallerid=yes*
*cidsignalling=dtmf*
*cidstart=ring*
*context=TEST_EXTERNAL*
*channel=>1-15*
*channel=>17-24*

This was the error message I was getting when I do "*module load chan_zap.so
*"

*[Oct  1 04:29:46] WARNING[17448]: chan_zap.c:905 zt_open: Unable to specify
channel 24: Device o       r resource busy*
*[Oct  1 04:29:46] ERROR[17448]: chan_zap.c:7219 mkintf: Unable to open
channel 24: Device or res       ource busy*
*here = 0, tmp->channel = 24, channel = 24*
*[Oct  1 04:29:46] ERROR[17448]: chan_zap.c:10582 build_channels: Unable to
register channel '17-       24'*


Now I changed *zapata.conf* to
*
*
*group=1*
*switchtype=euroisdn*
*signalling=pri_cpe*
*callerid=asreceived*
*usecallerid=yes*
*cidsignalling=dtmf*
*cidstart=ring*
*context=TEST_EXTERNAL*
*channel=>1-23*

Now the error is

*[Oct  1 04:33:03] ERROR[17612]: chan_zap.c:9470 start_pri: Unable to open
D-channel 24 (Device o       r resource busy)*
*[Oct  1 04:33:03] ERROR[17612]: chan_zap.c:11382 setup_zap: Unable to start
D-channel on span 1*

Do I need to mention the Data channel in zapata.conf??


My *zaptel.conf* is below. This was auto generated with *genzaptelconf -svdM
*
*
*
*# Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER)*
*span=1,1,0,esf,b8zs*
*# termtype: te*
*bchan=1-23*
*dchan=24*

I am using a *Digium TE122 Card* .  But when I do "*dmesg | wcte12xp*" I get
the following

*# dmesg | wcte12xp*
*
*
*wcte12xp 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21*
*wcte12xp: Setting up global serial parameters for T1*
*wcte12xp: Found a Wildcard TE122*
*wcte12xp: Span configured for ESF/B8ZS*
*wcte12xp: Setting yellow alarm*
*wcte12xp0: Missed interrupt. Increasing latency to 4 ms in order to
compensate.*
*wcte12xp 0000:04:00.0: PCI INT A disabled*
*wcte12xp 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21*
*wcte12xp: Setting up global serial parameters for T1*
*wcte12xp: Found a Wildcard TE122*
*wcte12xp: Span configured for ESF/B8ZS*
*wcte12xp: Setting yellow alarm*
*wcte12xp 0000:04:00.0: PCI INT A disabled*
*wcte12xp 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21*
*wcte12xp: Setting up global serial parameters for T1*
*wcte12xp: Found a Wildcard TE122*
*wcte12xp: Span configured for ESF/B8ZS*
*wcte12xp: Setting yellow alarm*
*wcte12xp: Span configured for ESF/B8ZS*
*wcte12xp: Span configured for ESF/B8ZS*
*wcte12xp 0000:04:00.0: PCI INT A disabled*
*wcte12xp 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21*
*wcte12xp: Setting up global serial parameters for T1*
*wcte12xp: Found a Wildcard TE122*
*wcte12xp: Span configured for ESF/B8ZS*
*wcte12xp: Setting yellow alarm*

Does the highlighted part mean that the card is setup in T1 mode. ??
( I do not have physical access to the server. But my support in the remote
office says that card is in E1 mode itself.. )

Thanks again for the help.
Najim
*
*



On Fri, Sep 30, 2011 at 1:40 PM, A J Stiles
<asterisk_list at earthshod.co.uk>wrote:

> On Friday 30 September 2011, NaJIm wrote:
> > Am I getting these error messages due to wrong configurations in my
> > zapata.conf.  ??
> >
> > I have got the following configurations in my zapata-channels.conf.
> >
> > ; Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER) B8ZS/ESF RED
> > group=0,11
> > context=from-pstn
> > switchtype = national
> > signalling = pri_cpe
> > channel => 1-23
> > group=
> > context=default
>
> Your Bearer channels should be 1 to 15 and 17 to 31  (or as high as they
> go,
> depending whether or not you paid for a full set of 30 lines),  with 16 as
> the
> Data channel.
>
> --
> AJS
>
> Answers come *after* questions.
>
> --
> _____________________________________________________________________
> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
> New to Asterisk? Join us for a live introductory webinar every Thurs:
>               http://www.asterisk.org/hello
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20111001/97275f5c/attachment.htm>