[asterisk-users] dahdi show status command not avilable in CLI
Eric Wieling
EWieling at nyigc.com
Fri Oct 7 08:49:17 CDT 2011
It is likely you have an error in your /etc/asterisk/chan_dahdi.conf
-----Original Message-----
From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of michael k
Sent: Friday, October 07, 2011 9:24 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] dahdi show status command not avilable in CLI
Hi,
I am getting this error message while executing the "module load chan_dahdi.so".
astrisks*CLI> module load chan_dahdi.so
Unable to load module chan_dahdi.so
Command 'module load chan_dahdi.so' failed.
== Parsing '/etc/asterisk/chan_dahdi.conf': == Found
== Parsing '/etc/asterisk/chan_dahdi_general.conf': == Found
== Parsing '/etc/asterisk/chan_dahdi_groups.conf': == Found
== Parsing '/etc/asterisk/dahdi-channels.conf': == Found
== Parsing '/etc/asterisk/chan_dahdi_additional.conf': == Found
Thanks,
Michael.k
On Thu, Oct 6, 2011 at 9:44 PM, Eric Wieling <EWieling at nyigc.com> wrote:
What happens when you do the module load chan_dahdi.so command?
-----Original Message-----
From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of michael k
Sent: Thursday, October 06, 2011 12:10 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] dahdi show status command not avilable in CLI
Hi,
astrisks*CLI> module unload chan_dahdi.so
Unable to unload resource chan_dahdi.so
Command 'module unload chan_dahdi.so ' failed.
Producing some other error messages !!!!!
On Thu, Oct 6, 2011 at 9:17 PM, Eric Wieling <EWieling at nyigc.com> wrote:
In the Asterisk CLI run the commands "module unload chan_dahdi.so" and "module load chan_dahdi.so".
-----Original Message-----
From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of michael k
Sent: Thursday, October 06, 2011 11:40 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] dahdi show status command not avilable in CLI
Hi,
I was run the commands "dahdi_genconf" and dahdi_cfg outside the CLI as the part of x100p card installation. Before issuing this command the dahdi show status command was available. There may any issues ?
Michael.k
On Thu, Oct 6, 2011 at 8:59 PM, gincantalupo <gincantalupo at fgasoftware.com> wrote:
Hi Michael,
what if you reload the module chan_dahdi from within the * CLI? It should give some hints.....
Giorgio
On 10/06/2011 05:22 PM, michael k wrote:
Hi Giorgio,
Thanks for your reply. I will produce some output for your reference.
# lsmod | grep dahdi
dahdi_echocan_mg2 39688 1
dahdi_transcode 42372 1 wctc4xxp
dahdi_voicebus 79424 2 wctdm24xxp,wcte12xp
dahdi 238384 14 dahdi_echocan_mg2,xpp,dahdi_transcode,wcb4xxp,wctdm,wcfxo,wctdm24xxp,wcte11xp,wct1xxp,wcte12xp,dahdi_voicebus,wct4xxp
crc_ccitt 35265 2 wctdm24xxp,dahdi
# service dahdi status
### Span 1: WCFXO/0 "Wildcard X100P Board 1" (MASTER)
1 FXO FXSKS (SWEC: MG2) (battery)
# dahdi_cfg -vv
DAHDI Tools Version - 2.3.0
DAHDI Version: 2.3.0.1
Echo Canceller(s): MG2
Configuration
======================
Channel map:
Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01)
1 channels to configure.
Setting echocan for channel 1 to mg2
# dahdi_scan
[1]
active=yes
alarms=OK
description=Wildcard X100P Board 1
name=WCFXO/0
manufacturer=Digium
devicetype=Wildcard X100P
location=PCI Bus 02 Slot 02
basechan=1
totchans=1
irq=193
type=analog
port=1,FXO
These outputs shows that the modules are loaded correctly. Any other clues ?
Michael.k
On Thu, Oct 6, 2011 at 8:43 PM, gincantalupo <gincantalupo at fgasoftware.com> wrote:
Hi Michael,
if you type "dah" followed by TAB and nothing appears, it means you do not have dahdi module loaded or dahdi_cfg application not launched before starting asterisk.
Giorgio
On 10/06/2011 04:57 PM, michael k wrote:
Hi All,
I have installed asteriskNow with Asterisk 1.6.2.11 and FreePBX 2.7.0.10. I have configured x100p fxo card in my asterisk box. But in my cli mode i am not getting the command "dahdi show status"
Output of CLI :
astrisks*CLI> dahdi show status
No such command 'dahdi show status' (type 'core show help dahdi show' for other possible commands)
I really not understand why this command is not avilable in CLI mode. Please help me to resolve this issue
Michael.k
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
More information about the asterisk-users
mailing list