[Asterisk-Users] Re: Problem setting up TDM22B card

[somesh s]

Hi,

And I have the digium's hardware too in one of my PCI 
slots.

Regards,
Somesh S. Shanbhag

--- somesh s <someshss at yahoo.com> wrote:

> Hi,
> 
> I know some bits about zaptel.conf and zapata.conf
> but
> 
> problem is modules wctdm, wcfxo, wcfxs are not
> getting
> loaded.
> 
> modprobe zaptel is successful!
> 
> Regards,
> Somesh S. Shanbhag
> 
> 
> 
> --- Tzafrir Cohen <tzafrir at cohens.org.il> wrote:
> 
> > On Sun, Sep 25, 2005 at 11:50:06PM -0700, somesh s
> > wrote:
> > > Hi,
> > > 
> > > I got the following output when I run the
> command.
> > > 
> > > >>>>>>>>>>>>>>> genzaptelconf -svd
> > >>>>>>>>>>>>>>>>
> > > 
> > > ./genzaptelconf: line 616: /etc/init.d/asterisk:
> > No
> > 
> > The script assumes that there is an
> > /etc/init.d/asterisk script.
> > 
> > Please stop asterisk manually.
> > 
> > > such file or directory
> > > Unloading zaptel modules:
> > > wcusb zaptel
> > > Test Loading modules:
> > >         -       zaptel
> > >         -       zaphfc
> > >         -       qozap
> > > Hint: insmod errors can be caused by incorrect
> > module
> > > parameters, including
> > > invalid IO or IRQ parameters.
> > >       You may find more information in syslog or
> > the
> > > output from dmesg
> > >         -       wctdm
> > > Hint: insmod errors can be caused by incorrect
> > module
> > > parameters, including
> > > invalid IO or IRQ parameters.
> > >       You may find more information in syslog or
> > the
> > > output from dmesg
> > >         -       wcfxo
> > > Hint: insmod errors can be caused by incorrect
> > module
> > > parameters, including
> > > invalid IO or IRQ parameters.
> > >       You may find more information in syslog or
> > the
> > > output from dmesg
> > >         -       wcfxs
> > >         -       pciradio
> > > Hint: insmod errors can be caused by incorrect
> > module
> > > parameters, including
> > > invalid IO or IRQ parameters.
> > >       You may find more information in syslog or
> > the
> > > output from dmesg
> > >         -       tor2
> > > Hint: insmod errors can be caused by incorrect
> > module
> > > parameters, including
> > > invalid IO or IRQ parameters.
> > >       You may find more information in syslog or
> > the
> > > output from dmesg
> > >         -       torisa
> > > Hint: insmod errors can be caused by incorrect
> > module
> > > parameters, including
> > > invalid IO or IRQ parameters.
> > >       You may find more information in syslog or
> > the
> > > output from dmesg
> > >         -       wct1xxp
> > > Hint: insmod errors can be caused by incorrect
> > module
> > > parameters, including
> > > invalid IO or IRQ parameters.
> > >       You may find more information in syslog or
> > the
> > > output from dmesg
> > >         -       wct4xxp
> > > Hint: insmod errors can be caused by incorrect
> > module
> > > parameters, including
> > > invalid IO or IRQ parameters.
> > >       You may find more information in syslog or
> > the
> > > output from dmesg
> > >         -       wcte11xp
> > >         -       wcusb
> > >         -       ztd_eth
> > 
> > It tries and fails to load many modules. This is
> > expected, as you don't
> > have their hardware.
> > 
> > However can you load any zaptel module using
> > modprobe?
> > What's the output of: 'lsmod | grep zaptel'
> > 
> > BTW: if you have a good idea of what should be in
> > zaptel.conf and
> > zapata.conf, I figure you should write them
> manually
> > and not waste too
> > much time on that automated script. It is meant to
> > save time, not to
> > spend time.
> > 
> > > Updating '/etc/default/zaptel'
> > > Generating '/etc/zaptel.conf'
> > > Generating '/etc/asterisk/zapata-channels.conf'
> > > Reconfiguring identified channels
> > >  
> > > Zaptel Configuration
> > > ======================
> > >  
> > >  
> > > Channel map:
> > >  
> > >  
> > > 0 channels configured.
> > >  
> > > ./genzaptelconf: line 653: /etc/init.d/asterisk:
> > No
> > > such file or directory
> > > Checking channels configured in Asterisk:
> > > ./genzaptelconf: line 665: asterisk: command not
> > found
> > > 
> > > >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
> > > 
> > > What may be the problem? Help me in this regard.
> > > 
> > > Regards,
> > > Somesh S. Shanbhag
> > > 
> > > --- Tzafrir Cohen <tzafrir at cohens.org.il> wrote:
> > > 
> > > > On Sun, Sep 25, 2005 at 10:42:52PM -0700,
> somesh
> > s
> > > > wrote:
> > > > > Hi,
> > > > > 
> > > > > Can you please give me some details about
> the
> > link
> > > > > you have sent? I am not aware of what it
> does?
> > > > > 
> > > > > [http://tzafrir.org.il/genzaptelconf]
> > > > 
> > > > It is a bash script for generating zaptel.conf
> > and
> > > > zapata.conf according
> > > > to the current settings.
> > > > 
> > > > To use it:
> > > > 
> > > > wget http://tzafrir.org.il/genzaptelconf
> > > > bash genzaptelconf -h # gives help
> > > > 
> > > > Try -s and -v . -d is probably not recommended
> > if
> > > > you have more thn one
> > > > card, I figure.
> > > > 
> > > > 
> > > > > 
> > > > > Regards,
> > > > > Somesh S. Shanbhag
> > > > > 
> > > > > --- Tzafrir Cohen <tzafrir at cohens.org.il>
> > wrote:
> > > > > 
> > > > > > On Fri, Sep 23, 2005 at 06:22:06AM -0700,
> > somesh
> > > > s
> > > > > > wrote:
> > > > > > > Hi Steve,
> > > > > > > 
> 
=== message truncated ===



		
__________________________________ 
Yahoo! Mail - PC Magazine Editors' Choice 2005 
http://mail.yahoo.com