[Asterisk-Users] TxFAX problem

[Vladyslav]

On Wed, 2005-03-16 at 18:25, Steve Underwood wrote:
> Hi Vladyslav,
> 
> The log looks good so far. The far end has negotiated. The fast modem 
> has been tested. Transmission of the first page has been. What happens 
> next. I don't think the log really stopped at that point. Did you wait 
> long enough for the page transmission to complete?

After that point "Changed from phase 3 to 6" 
fax machine says "Incomplete" + error code.
And that's all.

BTW, Fax machine connected via SIPURA-2000 (which registered directly on
* and use ulaw)
But I could receive fax from PSTN via *->SIPURA->Fax machine
 
> 
> Regards,
> Steve
> 
> 
> Vladyslav wrote:
> 
> >Here is new one : (but it's spandsp-0.0.2pre10)
> >
> >*CLI>     -- Executing NoOp("SIP/103-dfb6", "") in new stack
> >    -- Executing AGI("SIP/103-dfb6", "set-timestamp.agi") in new stack
> >    -- Executing System("SIP/103-dfb6", "echo "16032005-18:15:06 -
> >"VladK" <103> - SIP/103-dfb6 - 901" >> /var/log/asterisk/calls") in new
> >stack
> >    -- Executing DBput("SIP/103-dfb6", "RepeatDial/103=901") in new
> >stack
> >    -- DBput: family=RepeatDial, key=103, value=901
> >    -- Executing DBget("SIP/103-dfb6", "recv=Record/103") in new stack
> >    -- DBget: varname=recv, family=Record, key=103
> >    -- DBget: set variable recv to on
> >    -- Executing GotoIf("SIP/103-dfb6", "1?7:9") in new stack
> >    -- Goto (from-sip,901,7)
> >    -- Executing SetVar("SIP/103-dfb6",
> >"CALLFILENAME=20050316-181506-103-901") in new stack
> >    -- Executing Monitor("SIP/103-dfb6", "wav|20050316-181506-103-901")
> >in new stack
> >    -- Executing Goto("SIP/103-dfb6", "from-sip-post|901|1") in new
> >stack
> >    -- Goto (from-sip-post,901,1)
> >    -- Executing Answer("SIP/103-dfb6", "") in new stack
> >    -- Executing TxFAX("SIP/103-dfb6", "/tmp/testfax.tif|caller") in new
> >stack
> >Slow carrier up
> >Mar 16 18:15:10 NOTICE[10168]: rtp.c:540 ast_rtp_read: Unknown RTP codec
> >100 received
> >Slow carrier down
> >Slow carrier up
> >Slow carrier down
> >Slow carrier up
> ><<< NSF: 20 00 00 79 00 00 00 82 0f 09 03 10 10 00 02 95 80 9c f8 80 40
> >01 49 02 41 52 41 59 4f 5a 20 55 4b 52 41 49 4e 45 23 20 03
> >NSF without final frame tag
> >The remote was made by 'Panasonic'
> ><<< DIS: 80 20 ee 99 84 80 11
> >DIS with final frame tag
> >In state 10
> >DIS:
> >  V.8 capable
> >  Prefer 256 octet blocks
> >  Can receive fax
> >  Supported data signalling rates: V.27ter, V.29 and V.17
> >  R8x7.7lines/mm and/or 200x200pels/25.4mm
> >  2D coding
> >  Scan line length: 215mm or 255mm
> >  Recording length: A4 (297mm) and B4 (364mm)
> >  Receiver's minimum scan line time: 5ms at 3.85 l/mm: T7.7 = T3.85
> >  Error correction mode
> >  R8x15.4lines/mm
> >  Metric-based resolution preferred
> >  Minimum scan line time for higher resolutions: T15.4 = T7.7
> >DCS:
> >  Can receive fax
> >  Selected data signalling rate: V.29, 9600bps
> >  2D coding
> >  Scan line length: 215mm
> >  Recording length: A4 (297mm)
> >  Minimum scan line time: 20ms
> >  Minimum scan line time for higher resolutions: T15.4 = T7.7
> >Start sending document
> >Start tx document
> >Changed from phase 2 to 4
> >  
> >
> >>>>DCS: 83 00 c6 80 80 80 00
> >>>>        
> >>>>
> >HDLC underflow in state 3
> >Changed from phase 4 to 6
> >Changed from phase 6 to 3
> >Slow carrier up
> ><<< CFR: 84
> >CFR with final frame tag
> >In state 4
> >Trainability test succeeded
> >Start tx page
> >Slow carrier down
> >Changed from phase 3 to 6
> >
> >*CLI> show ch
> >channel       channels      channeltypes
> >*CLI> show channels
> >        Channel  (Context    Extension    Pri )   State Appl.        
> >Data
> >0 active channel(s)
> >  
> >
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users