[Asterisk-Users] TxFAX problem

[Steve Underwood]

Hi Vladyslav,

The log looks good so far. The far end has negotiated. The fast modem 
has been tested. Transmission of the first page has been. What happens 
next. I don't think the log really stopped at that point. Did you wait 
long enough for the page transmission to complete?

Regards,
Steve


Vladyslav wrote:

>Here is new one : (but it's spandsp-0.0.2pre10)
>
>*CLI>     -- Executing NoOp("SIP/103-dfb6", "") in new stack
>    -- Executing AGI("SIP/103-dfb6", "set-timestamp.agi") in new stack
>    -- Executing System("SIP/103-dfb6", "echo "16032005-18:15:06 -
>"VladK" <103> - SIP/103-dfb6 - 901" >> /var/log/asterisk/calls") in new
>stack
>    -- Executing DBput("SIP/103-dfb6", "RepeatDial/103=901") in new
>stack
>    -- DBput: family=RepeatDial, key=103, value=901
>    -- Executing DBget("SIP/103-dfb6", "recv=Record/103") in new stack
>    -- DBget: varname=recv, family=Record, key=103
>    -- DBget: set variable recv to on
>    -- Executing GotoIf("SIP/103-dfb6", "1?7:9") in new stack
>    -- Goto (from-sip,901,7)
>    -- Executing SetVar("SIP/103-dfb6",
>"CALLFILENAME=20050316-181506-103-901") in new stack
>    -- Executing Monitor("SIP/103-dfb6", "wav|20050316-181506-103-901")
>in new stack
>    -- Executing Goto("SIP/103-dfb6", "from-sip-post|901|1") in new
>stack
>    -- Goto (from-sip-post,901,1)
>    -- Executing Answer("SIP/103-dfb6", "") in new stack
>    -- Executing TxFAX("SIP/103-dfb6", "/tmp/testfax.tif|caller") in new
>stack
>Slow carrier up
>Mar 16 18:15:10 NOTICE[10168]: rtp.c:540 ast_rtp_read: Unknown RTP codec
>100 received
>Slow carrier down
>Slow carrier up
>Slow carrier down
>Slow carrier up
><<< NSF: 20 00 00 79 00 00 00 82 0f 09 03 10 10 00 02 95 80 9c f8 80 40
>01 49 02 41 52 41 59 4f 5a 20 55 4b 52 41 49 4e 45 23 20 03
>NSF without final frame tag
>The remote was made by 'Panasonic'
><<< DIS: 80 20 ee 99 84 80 11
>DIS with final frame tag
>In state 10
>DIS:
>  V.8 capable
>  Prefer 256 octet blocks
>  Can receive fax
>  Supported data signalling rates: V.27ter, V.29 and V.17
>  R8x7.7lines/mm and/or 200x200pels/25.4mm
>  2D coding
>  Scan line length: 215mm or 255mm
>  Recording length: A4 (297mm) and B4 (364mm)
>  Receiver's minimum scan line time: 5ms at 3.85 l/mm: T7.7 = T3.85
>  Error correction mode
>  R8x15.4lines/mm
>  Metric-based resolution preferred
>  Minimum scan line time for higher resolutions: T15.4 = T7.7
>DCS:
>  Can receive fax
>  Selected data signalling rate: V.29, 9600bps
>  2D coding
>  Scan line length: 215mm
>  Recording length: A4 (297mm)
>  Minimum scan line time: 20ms
>  Minimum scan line time for higher resolutions: T15.4 = T7.7
>Start sending document
>Start tx document
>Changed from phase 2 to 4
>  
>
>>>>DCS: 83 00 c6 80 80 80 00
>>>>        
>>>>
>HDLC underflow in state 3
>Changed from phase 4 to 6
>Changed from phase 6 to 3
>Slow carrier up
><<< CFR: 84
>CFR with final frame tag
>In state 4
>Trainability test succeeded
>Start tx page
>Slow carrier down
>Changed from phase 3 to 6
>
>*CLI> show ch
>channel       channels      channeltypes
>*CLI> show channels
>        Channel  (Context    Extension    Pri )   State Appl.        
>Data
>0 active channel(s)
>  
>