[Asterisk-Users] Asterisk - libunicall - MFCr2 *** settings problems ***

[kaws elchamal]

Dear Steve and *.* e1r2 developers and users,

now MFCR2 is successfully installed! many thanks for
your help.

I'm living in Argelia. I have configure my MFCR2
according argentina R2 settigs. (look at the end of
the message)

the testcall run perfectly (only warnings and I think
that is just debug).
but I have many problems and when I run
Asterisk-MFCR2, generally in the begging no errors
occures. after random time many inopportune errors
occures:
sound-cuts, dumb intervals, drop calls and
disconnections!!!

I think that R2 settings I use are not adapted to
Argelian R2 settings. I will try change them but I
have not idea where I must do changes. Please help me.

Regards,

kaws


P.S: in the following: my configuration - Argelian R2
parameters and an example of error.

***********************
my configuration  is :


unical.conf:

protocolclass=mfcr2
protocolvariant=ar,20,4
protocolend=cpe
span=1,1,0,cas,hdb3
cas=1-15:1101
cas=17-31:1101
loadzone=us
defaultzone=us

zaptel.conf:

span=1,1,0,cas,hdb3
cas=1-15:1101
cas=17-31:1101


*****************************************************
the R2 setting of argelia according to quintum are : 

CD-Bits ::::::::::::::::::::::: 0001
Invert-Bits ::::::::::::::::::: 0000
DNIS Length ::::::::::::::::::: 9 digits *
Answer Tone ::::::::::::::::::: A-6
Send 1st Digit :::::::::::::::: 1
Group B Xmt Idle Tone ::::::::: B-6
Group B Xmt Busy Tone ::::::::: B-3
Group B Rcv Idle Tones :::::::: B-2 & B-3
Group B Rcv Busy Tones :::::::: B-1 & B-2
ANI Request ::::::::::::::::::: Do not request ANI
ANI Length
ANI Category Request
Tone ANI Tone Request
ANI Category :::::::::::::::::: I-1
ANI Calling Party Category :::: II-1
Seizure Ack Timeout ::::::::::: 150ms
Release Guard Timeout ::::::::: 600ms
* Always double-check the DNIS length with your
carrier

***************************************************
example of inopportune disconnection:

Jan 17 10:04:17 WARNING[-1120736336]:
chan_unicall.c:634 unicall_error: UniCall: mfcr2 Rx
bits 0x9   [1/      20/103/107]
Jan 17 10:04:17 WARNING[-1120736336]:
chan_unicall.c:634 unicall_error: UniCall: mfcr2 Far
end disconnected - state 0x20
Jan 17 10:04:17 WARNING[-1120736336]:
chan_unicall.c:2548 handle_uc_event: UC event Far end
disconnected
Jan 17 10:04:17 WARNING[-1120736336]:
chan_unicall.c:2854 handle_uc_event: Far disconnect
cause 16
Jan 17 10:04:17 WARNING[-1120736336]:
chan_unicall.c:1088 unicall_hangup:
unicall_hangup(UniCall/5-1)
Jan 17 10:04:17 WARNING[-1120736336]:
chan_unicall.c:1263 unicall_hangup: Causes 0 16
Jan 17 10:04:17 WARNING[-1120736336]:
chan_unicall.c:634 unicall_error: UniCall: mfcr2
mfcr2_DropCall()
Jan 17 10:04:17 WARNING[-1120736336]:
chan_unicall.c:634 unicall_error: UniCall: mfcr2 Call
disconnected - state 0x800
Jan 17 10:04:17 WARNING[-1114432592]:
chan_unicall.c:2548 handle_uc_event: UC event Drop
call
Jan 17 10:04:17 WARNING[-1114432592]:
chan_unicall.c:2892 handle_uc_event: Doing a
uc_ReleaseCall
Jan 17 10:04:17 WARNING[-1114432592]:
chan_unicall.c:634 unicall_error: UniCall: mfcr2
mfcr2_ReleaseCall()
Jan 17 10:04:17 WARNING[-1114432592]:
chan_unicall.c:634 unicall_error: UniCall: mfcr2 Tx
bits 0x9   [1/    1000/106/107]
Jan 17 10:04:17 WARNING[-1114432592]:
chan_unicall.c:634 unicall_error: UniCall: mfcr2
Destroying call with CRN 32769
Jan 17 10:04:17 WARNING[-1114432592]:
chan_unicall.c:634 unicall_error: UniCall: mfcr2
release_guard_expired
Jan 17 10:04:17 WARNING[-1114432592]:
chan_unicall.c:2548 handle_uc_event: UC event Release
call


		
__________________________________ 
Do you Yahoo!? 
Yahoo! Mail - Helps protect you from nasty viruses. 
http://promotions.yahoo.com/new_mail