[Asterisk-Users] TE410P E1 Red Alarm

Sun Dec 25 02:33:46 MST 2005

Firstly, try unplugging span 1 and plug it into spans 2,3,4 in turn to
check the port. 

Secondly, try E1 crossover cables in the remaining red-alarm spans.

Regards,

Mark

-----Original Message-----
From: Diyanat Ali [mailto:diyanat at hotmail.com] 
Sent: Sunday, 25 December 2005 8:08 PM
To: asterisk-users at lists.digium.com
Subject: [Asterisk-Users] TE410P E1 Red Alarm

Hello!

I have a TE410P quad span card with 4 E1, i am using asterisk 1.2.1, i
was 
using it without any issues earlier with just 1 E1 on span 1 and i
recently 
plugged in 3 more E1's, only span 1 is working, the e1 for span 1 is
from a 
different provider then the rest, the settings are same for both, but i 
constantly get red alaram on the span 2,3,4, i tried all settings,
including 
the timming source , framing, coding , signalling type etc, without any 
sucesss

what maybe the cause of the red alarm

Regards

Diyanat

lspci -vvv
06:01.0 Communication controller: Unknown device d161:0410 (rev 02)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ 
Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-

<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Interrupt: pin A routed to IRQ 74
        Region 0: Memory at fdff0000 (32-bit, non-prefetchable)
[size=128]

lsmod
Module                  Size  Used by    Not tainted
wct4xxp                78432 124
zaptel                183776 250  [wct4xxp]

cat /proc/zaptel/*
Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4
1 TE4/0/1/1 Clear (In use) .... upto
16 TE4/0/1/16 HDLCFCS (In use) .... upto
31 TE4/0/1/31 Clear (In use)
Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" HDB3/CCS/CRC4 RED
32 TE4/0/2/1 Clear (In use) .... upto
47 TE4/0/2/16 HDLCFCS (In use) .... upto
62 TE4/0/2/31 Clear (In use)
Span 3: TE4/0/3 "T4XXP (PCI) Card 0 Span 3" HDB3/CCS/CRC4 RED
63 TE4/0/3/1 Clear (In use) .... upto
78 TE4/0/3/16 HDLCFCS (In use) .... upto
93 TE4/0/3/31 Clear (In use)
Span 4: TE4/0/4 "T4XXP (PCI) Card 0 Span 4" HDB3/CCS/CRC4 RED
94 TE4/0/4/1 Clear (In use) .... upto
109 TE4/0/4/16 HDLCFCS (In use) .... upto
124 TE4/0/4/31 Clear (In use)

ztcfg -v
SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
SPAN 2: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
SPAN 3: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
SPAN 4: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
124 channels configured.

zttool
Alarms          Span
OK              T4XXP (PCI) Card 0 Span 1
RED             T4XXP (PCI) Card 0 Span 2
RED             T4XXP (PCI) Card 0 Span 3
RED             T4XXP (PCI) Card 0 Span 4

CLI> zap show status
Description                              Alarms     IRQ        bpviol

CRC4
T4XXP (PCI) Card 0 Span 1                OK         0          0
0
T4XXP (PCI) Card 0 Span 2                RED        0          0
0
T4XXP (PCI) Card 0 Span 3                RED        0          0
0
T4XXP (PCI) Card 0 Span 4                RED        0          0
0

alpha*CLI> pri show span 1
Primary D-channel: 16
Status: Provisioned, Up, Active
Switchtype: EuroISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: 0
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T313 Timer: 4000
N200 Counter: 3

alpha*CLI> pri show span 2
Primary D-channel: 47
Status: Provisioned, In Alarm, Down, Active
Switchtype: EuroISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: 0
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T313 Timer: 4000
N200 Counter: 3
its the same as span for the rest as upto span 4

CLI>pri intense debug span 2
>Unnumbered frame:
>SAPI: 00  C/R: 0 EA: 0
>  TEI: 000        EA: 1
>   M3: 3   P/F: 1 M2: 3 11: 3  [ SABME (set asynchronous balanced mode 
>extended) ]
>0 bytes of data
Sending Set Asynchronous Balanced Mode Extended

same for the rest

zaptel.conf
span=1,1,0,ccs,hdb3,crc4
bchan = 1-15
dchan = 16
bchan = 17-31
span=2,1,0,ccs,hdb3,crc4
bchan = 32-46
dchan = 47
bchan = 48-62
span=3,1,0,ccs,hdb3,crc4
bchan = 63-77
dchan = 78
bchan = 79-93
span=4,1,0,ccs,hdb3,crc4
bchan = 94-108
dchan = 109
bchan = 110-124
loadzone=se
defaultzone=se

zapata.conf
[channels]
language=us
context=sip
switchtype=euroisdn
pridialplan=unknown
prilocaldialplan=unknown
signalling=pri_cpe
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
echotraining=yes
cidsignalling=dtmf
cidstart=ring
rxgain=0.0
txgain=0.0
group=1
callgroup=1
pickupgroup=1
immediate=no
callerid=asreceived

group=1
channel => 1-15
channel => 17-31

group=2
channel => 32-46
channel => 48-62

group=3
channel => 63-77
channel => 79-93

group=4
channel => 94-108
channel => 110-124

_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users