[Asterisk-Users] TE405P V2 changes?

[Kib Eki]

yes, fedora 3 but without any changes at the sources

Master Abi wrote:
> Are you using Redhat/Fedora? If I remember those init scripts is for 
> Redhat/Fedora. I am using gentoo.
> 
> Did you make any modifications to wct4xxp.c. or pass any parameters to 
> zaptel. I see there is a #define SUPPORT_GEN1 in to wct4xxp.c which I 
> commented out, but it made no difference. ztcfg seems to where the 
> channels become unassigned.
> 
> Thanks again.
> 
> Kib Eki wrote:
> 
>> Hi,
>> we also got one V2 TE405P card. It works fine now. At the moment we 
>> use for bridging the Pri to our old PBX.
>> You must use zaptel, libri and asterisk v 1.0.8 or higher. We use 
>> 1.0.9 at the moment.
>> zaptel:
>> after make; make install i also executed make config. This copies the 
>> correct startup script to /etc/init.d/zaptel. Without this it also 
>> didn't worked for me.
>>
>>
>>
>> Master Abi wrote:
>>
>>> Hi
>>>
>>> I got the 2nd Gen firmware upgraded on the TE405P.  I recompiled 
>>> after putting in the upgraded board but did not change any conf, but 
>>> the spans become active but will not come up.
>>>
>>> I guess I am missing something or are the any changes to the 
>>> zaptel/libpri software that is required. I cannot find any info about 
>>> this or does this new firmware only work with latest CVS. I am using 
>>> 1.0.9 with 2.6.12 kernel
>>>
>>> Zapata Telephony Interface Registered on major 196
>>> Found TE4XXP at base address fdfff000, remapped to f8928000
>>> TE4XXP version c01a0164, burst ON, slip debug: OFF
>>> TE4XXP running with work queues.
>>> FALC version: 00000005, Board ID: 00
>>> Reg 0: 0x364e9400
>>> Reg 1: 0x364e9000
>>> Reg 2: 0xffffffff
>>> Reg 3: 0x00000000
>>> Reg 4: 0x00000001
>>> Reg 5: 0x00000000
>>> Reg 6: 0xc01a0164
>>> Reg 7: 0x00001f00
>>> Reg 8: 0x00000000
>>> Reg 9: 0x00ff0000
>>> Reg 10: 0x00000000
>>> TE4XXP: Launching card: 0
>>> TE4XXP: Setting up global serial parameters
>>> Found a Wildcard: Wildcard TE405P (2nd Gen)
>>> eth0: link up, 10Mbps, half-duplex, lpa 0x0000
>>> About to enter spanconfig!
>>> Done with spanconfig!
>>> About to enter spanconfig!
>>> Done with spanconfig!
>>> Unassigning channel 0/1!
>>> Unassigning channel 0/2!
>>> Unassigning channel 0/3!
>>> Unassigning channel 0/4!
>>> Unassigning channel 0/5!
>>> Unassigning channel 0/6!
>>> Unassigning channel 0/7!
>>> Unassigning channel 0/8!
>>> Unassigning channel 0/9!
>>> Unassigning channel 0/10!
>>> Unassigning channel 0/11!
>>> Unassigning channel 0/12!
>>> Unassigning channel 0/13!
>>> Unassigning channel 0/14!
>>> Unassigning channel 0/15!
>>> Unassigning channel 0/16!
>>> Unassigning channel 0/17!
>>> Unassigning channel 0/18!
>>> etc...
>>>
>>> This was working for 10 months before the upgrade.
>>>
>>> Master
>>>
>>>
>>> _______________________________________________
>>> Asterisk-Users mailing list
>>> Asterisk-Users at lists.digium.com
>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>> To UNSUBSCRIBE or update options visit:
>>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>>>
>>>
>>
>> _______________________________________________
>> Asterisk-Users mailing list
>> Asterisk-Users at lists.digium.com
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>> To UNSUBSCRIBE or update options visit:
>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
> 
>