[Asterisk-Users] TE405P V2 changes?

[Master Abi]

Are you using Redhat/Fedora? If I remember those init scripts is for 
Redhat/Fedora. I am using gentoo.

Did you make any modifications to wct4xxp.c. or pass any parameters to 
zaptel. I see there is a #define SUPPORT_GEN1 in to wct4xxp.c which I 
commented out, but it made no difference. ztcfg seems to where the 
channels become unassigned.

Thanks again.

Kib Eki wrote:
> Hi,
> we also got one V2 TE405P card. It works fine now. At the moment we use 
> for bridging the Pri to our old PBX.
> You must use zaptel, libri and asterisk v 1.0.8 or higher. We use 1.0.9 
> at the moment.
> zaptel:
> after make; make install i also executed make config. This copies the 
> correct startup script to /etc/init.d/zaptel. Without this it also 
> didn't worked for me.
> 
> 
> 
> Master Abi wrote:
> 
>> Hi
>>
>> I got the 2nd Gen firmware upgraded on the TE405P.  I recompiled after 
>> putting in the upgraded board but did not change any conf, but the 
>> spans become active but will not come up.
>>
>> I guess I am missing something or are the any changes to the 
>> zaptel/libpri software that is required. I cannot find any info about 
>> this or does this new firmware only work with latest CVS. I am using 
>> 1.0.9 with 2.6.12 kernel
>>
>> Zapata Telephony Interface Registered on major 196
>> Found TE4XXP at base address fdfff000, remapped to f8928000
>> TE4XXP version c01a0164, burst ON, slip debug: OFF
>> TE4XXP running with work queues.
>> FALC version: 00000005, Board ID: 00
>> Reg 0: 0x364e9400
>> Reg 1: 0x364e9000
>> Reg 2: 0xffffffff
>> Reg 3: 0x00000000
>> Reg 4: 0x00000001
>> Reg 5: 0x00000000
>> Reg 6: 0xc01a0164
>> Reg 7: 0x00001f00
>> Reg 8: 0x00000000
>> Reg 9: 0x00ff0000
>> Reg 10: 0x00000000
>> TE4XXP: Launching card: 0
>> TE4XXP: Setting up global serial parameters
>> Found a Wildcard: Wildcard TE405P (2nd Gen)
>> eth0: link up, 10Mbps, half-duplex, lpa 0x0000
>> About to enter spanconfig!
>> Done with spanconfig!
>> About to enter spanconfig!
>> Done with spanconfig!
>> Unassigning channel 0/1!
>> Unassigning channel 0/2!
>> Unassigning channel 0/3!
>> Unassigning channel 0/4!
>> Unassigning channel 0/5!
>> Unassigning channel 0/6!
>> Unassigning channel 0/7!
>> Unassigning channel 0/8!
>> Unassigning channel 0/9!
>> Unassigning channel 0/10!
>> Unassigning channel 0/11!
>> Unassigning channel 0/12!
>> Unassigning channel 0/13!
>> Unassigning channel 0/14!
>> Unassigning channel 0/15!
>> Unassigning channel 0/16!
>> Unassigning channel 0/17!
>> Unassigning channel 0/18!
>> etc...
>>
>> This was working for 10 months before the upgrade.
>>
>> Master
>>
>>
>> _______________________________________________
>> Asterisk-Users mailing list
>> Asterisk-Users at lists.digium.com
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>> To UNSUBSCRIBE or update options visit:
>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>>
>>
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>