[Asterisk-Users] Problems installing x100p

[Lyle Giese]

It might help if you tried to modprobe the right module.  Try wcfxo instead.

wcfxo is for the x10xp cards
wcfxs is for the TDM cards irregardless of the modules installed.

And the use of the -v parameter on all these commands would be helpfull.

Lyle

----- Original Message ----- 
From: "Rodolfo Grave" <rodolfograve at yahoo.es>
To: "Asterisk Users Mailing List - Non-Commercial Discussion"
<asterisk-users at lists.digium.com>
Sent: Sunday, September 12, 2004 6:50 AM
Subject: [Asterisk-Users] Problems installing x100p


> Hi.
>
> I have succesfuly installed asterisk and after I added a x100p card, but
> the system doesn't seem to know the card is there. This is what I've done:
>
> compiled and installed zaptel, libpri and asterisk in that order using
> "make clean ; make install" commands. also, "make samples" for asterisk.
>
> shutdown the PC and installed the x100p PCI card.
>
> execute the following commands (I also include the output):
>
> linux# ] modprobe zaptel
> linux# ] modprobe wcfxs
> /lib/modules/2.4.21-99-default/misc/wcfxs.o: init_module: No such device
> /lib/modules/2.4.21-99-default/misc/wcfxs.o: insmod
> /lib/modules/2.4.21-99-default/misc/wcfxs.o failed
> /lib/modules/2.4.21-99-default/misc/wcfxs.o: insmod wcfxs failed
> Hint: insmod errors can be caused by incorrect module parameters,
> including invalid IO or IRQ parameters.
>       You may find more information in syslog or the output from dmesg
> linux# ] lspci
> 00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo
> PRO133x] (rev 22)
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo
> MVP3/Pro133x AGP]
> 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C596 ISA [Mobile South]
> (rev 09)
> 00:07.1 IDE interface: VIA Technologies, Inc.
> VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06)
> 00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 02)
> 00:07.3 Host bridge: VIA Technologies, Inc. VT82C596 Power Management
> 00:0a.0 Ethernet controller: MYSON Technology Inc SURECOM EP-320X-S
> 100/10M Ethernet PCI Adapter
> 00:0c.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev
10)
> 00:0c.1 Communication controller: C-Media Electronics Inc CM8738 (rev 10)
> 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS]
> 86C326 5598/6326 (rev 0b)
>
> It seems that the PCI card is not detected... any ideas?
>
> Thanks in advance.
>
> RODOLFO
>
>
>
>
> ---
> avast! Antivirus: Outbound message clean.
> Virus Database (VPS): 0437-1, 09/09/2004
> Tested on: 12/09/2004 13:50:10
> avast! - copyright (c) 2000-2004 ALWIL Software.
> http://www.avast.com
>
>
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>