[Asterisk-Users] pri with TE410P not working (Austria)

[Michael Bielicki]

Throw out the yellow.
Check if for sure the other side is using crc4.

On Thu, 2004-06-17 at 10:45, Wolfgang Pichler wrote:
> Am Do, den 17.06.2004 schrieb Michael Bielicki um 10:32:
> > What is in your config file ?
> i've already posted my config in my first post - but here is my
> /etc/zaptel.conf
> --------------------------------
> span=1,1,0,ccs,hdb3,crc4,yellow
> span=2,2,0,ccs,hdb3,crc4,yellow
> bchan=1-15,17-31
> dchan=16
> bchan=32-46,48-62
> dchan=47
> 
> loadzone=at
> defaultzone=at
> --------------------------------
> 
> and my /etc/asterisk/zaptel.conf
> --------------------------------
> [channels]
> switchtype = euroisdn
> signalling = pri_cpe
> pridialplan = local
> group = 1
> context = default
> channel => 1-15,17-31
> 
> switchtype = euroisdn
> signalling = pri_cpe
> pridialplan = local
> group = 2
> context=default
> channel => 32-46,48-62
> ----------------------------
> 
> > zaptel.conf ?
> > also, check the crc4 settings
> which crc4 settings ? - i've thought crc4 could only be turned on or off
> ?
> > and
> > maybe the wire you are using is wrong since some equippment needs
> > crossed wires, some needs straight wires. Crossed would be 1-4 2-5
> i've already tried to use crossed wires - didn't worked either
> 
> > 
> > cheers
> > 
> > Michael
> > 
> > On Thu, 2004-06-17 at 10:28, Wolfgang Pichler wrote:
> > > Am Do, den 17.06.2004 schrieb Peter Svensson um 9:43:
> > > > On Thu, 17 Jun 2004, Wolfgang Pichler wrote:
> > > > 
> > > > > ... on the card i can see the two leds pulsing red (i think thats the
> > > > > yellow alaram - or i am wrong) ?
> > > > 
> > > > Are you sure it is not a red alarm? That would indicate a loss of link. 
> > > > I think you can check with the command zttool. 
> > > you are right - its a red alarm - zttool says "Red Alarm/Not Open"
> > > > 
> > > > Are you sure the cables are correct? 
> > > > Have you set the jumpers on the card to E1 and not left them on T1?
> > > The jumpers are on E1 - the cables should be ok (they are working with
> > > other hardware) - and the card is directly connected to a simens ULAF+
> > > STU Desktop (can't really find much information about this device on the
> > > net) - which turns off a red led when i load the driver and do a ztcfg.
> > > > 
> > > > I think the leds should turn green when the card senses a correct carrier
> > > > and framing on the lines.
> > > green is always a wounderful color ;-)
> > > 
> > > so, what else could cause this ?
> > > 
> > > wolfgang
> > > 
> > > _______________________________________________
> > > Asterisk-Users mailing list
> > > Asterisk-Users at lists.digium.com
> > > http://lists.digium.com/mailman/listinfo/asterisk-users
> > > To UNSUBSCRIBE or update options visit:
> > >    http://lists.digium.com/mailman/listinfo/asterisk-users
> > 
> > _______________________________________________
> > Asterisk-Users mailing list
> > Asterisk-Users at lists.digium.com
> > http://lists.digium.com/mailman/listinfo/asterisk-users
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-users
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users