[Asterisk-Users] TE410P in Austria

[Wolfgang Pichler]

hi all,

i have now enabled pri debugging with "pri intense debug span"

so i get:
--------------------
> Unnumbered frame:
> SAPI: 00  C/R: 0 EA: 0
>  TEI: 000        EA: 1
>   M3: 3   P/F: 1 M2: 3 11: 3  [ SABME (set asynchronous balanced mode
extended) ]
> 0 bytes of data
Urgent handler
Sending Set Asynchronous Balanced Mode Extended
--------------------
what does this all means ?

best regards
Wolfgang

Am Mo, den 14.06.2004 schrieb Wolfgang Pichler um 14:06:
> i've changed it now - but i still get the yellow alarm (i've changed it
> to: span=1,1,0,ccs,hdb3,crc4,yellow)
> 
> this is my dmesg output after ztcfg -v
> -------------
> Found TE410P at base address 40100000, remapped to d8b15000
> TE410P version c01a009b
> FALC version: 00000005, Board ID: 00
> Reg 0: 0x124b1800
> Reg 1: 0x124b1000
> Reg 2: 0x07fc07fc
> Reg 3: 0x00000000
> Reg 4: 0x00000000
> Reg 5: 0x00000000
> Reg 6: 0xc01a009b
> Reg 7: 0x00001f00
> Reg 8: 0x00000000
> Reg 9: 0x00ff0000
> Reg 10: 0x00000000
> TE410P: Launching card: 0
> TE410P: Setting up global serial parameters
> Found a Wildcard: Wildcard TE410P-Xilinx
> Registered tone zone 9 (Austria)
> TE410P: Span 1 configured for CCS/HDB3/CRC4
> SPAN 1: Primary Sync Source
> TE410P: Span 2 configured for CCS/HDB3/CRC4
> SPAN 2: Secondary Sync Source
> wct4xxp: Setting yellow alarm on span 1
> wct4xxp: Setting yellow alarm on span 2
> -------------------
> 
> any other ideas ?
> 
> best regards
> Wolfgang
> 
> Am Mo, den 14.06.2004 schrieb Jason Williams um 12:44:
> > Wolfgang,
> > 
> > You need to use ccs not cas
> > 
> > 
> > I would change your timing options to these:-
> > 
> > 
> > -------------/etc/zaptel.conf----------------
> >   span=1,1,0,ccs,hdb3,crc4
> >   span=2,2,0,ccs,hdb3,crc4
> >   bchan=1-15
> >   bchan=17-31
> >   bchan=32-46
> >   bchan=48-62
> >   dchan=16
> >   dchan=47
> > 
> > 
> > That should work
> > 
> > 
> > At 12:33 14/06/2004 +0200, you wrote:
> > >sorry, i don't know what you mean with: Is it the same as Telstra -
> > >could you please clearify this ?
> > >
> > >wolfgang
> > >
> > >Am Mo, den 14.06.2004 schrieb Michael M. Saunders um 12:25:
> > > > Is it the same as Telstra
> > > >
> > > > -----Original Message-----
> > > > From: asterisk-users-admin at lists.digium.com
> > > > [mailto:asterisk-users-admin at lists.digium.com] On Behalf Of Wolfgang
> > > > Pichler
> > > > Sent: Monday, 14 June 2004 8:11 PM
> > > > To: Asterisk-Users Mailinglist
> > > > Subject: [Asterisk-Users] TE410P in Austria
> > > >
> > > > hi all,
> > > >
> > > > i've now installed a TE410P (Quad T1/E1 Primary Card - Digium) and
> > > > connected it to a primary line. My telco (eTel) only told me that they
> > > > are using hdb3 and crc4. So i still don't know which coding i have to
> > > > use (cas or ccs) - and what timing options i have to use.
> > > >
> > > > Have someone already get a card like this up in Austria with a line from
> > > > eTel or from the telekom Austria ?
> > > >
> > > > Another technics told me that it could be that i will need a different
> > > > cable - could this be ?
> > > >
> > > > At time my configuration is:
> > > > -------------/etc/zaptel.conf----------------
> > > > span=1,1,0,ccs,hdb3,crc4
> > > > span=2,1,0,ccs,hdb3,crc4
> > > > bchan=1-15
> > > > bchan=17-31
> > > > bchan=32-46
> > > > bchan=48-62
> > > > dchan=16
> > > > dchan=47
> > > >
> > > > loadzone=at
> > > > defaultzone=at
> > > >
> > > > -----------/etc/asterisk/zaptel.conf-------------
> > > > [channels]
> > > > switchtype = euroisdn
> > > > signalling = pri_cpe
> > > > pridialplan = local
> > > > group = 1
> > > > context = default
> > > > channel => 1-15
> > > > channel => 17-31
> > > >
> > > > switchtype = euroisdn
> > > > signalling = pri_cpe
> > > > pridialplan = local
> > > > group = 2
> > > > context=default
> > > > channel => 32-46
> > > > channel => 48-62
> > > >
> > > > Another thing - for the wct4xxp module - do i really need to restart the
> > > > whole pc so that changes in /etc/zaptel.conf take effect, or do i only
> > > > need to reinsert the module - rerun ztcfg ?
> > > >
> > > > hope someone here can help me
> > > >
> > > > best regards
> > > > Wolfgang
> > > >
> > > > _______________________________________________
> > > > Asterisk-Users mailing list
> > > > Asterisk-Users at lists.digium.com
> > > > http://lists.digium.com/mailman/listinfo/asterisk-users
> > > > To UNSUBSCRIBE or update options visit:
> > > >    http://lists.digium.com/mailman/listinfo/asterisk-users
> > > >
> > > >
> > > > _______________________________________________
> > > > Asterisk-Users mailing list
> > > > Asterisk-Users at lists.digium.com
> > > > http://lists.digium.com/mailman/listinfo/asterisk-users
> > > > To UNSUBSCRIBE or update options visit:
> > > >    http://lists.digium.com/mailman/listinfo/asterisk-users
> > >
> > >_______________________________________________
> > >Asterisk-Users mailing list
> > >Asterisk-Users at lists.digium.com
> > >http://lists.digium.com/mailman/listinfo/asterisk-users
> > >To UNSUBSCRIBE or update options visit:
> > >    http://lists.digium.com/mailman/listinfo/asterisk-users
> > 
> > _______________________________________________
> > Asterisk-Users mailing list
> > Asterisk-Users at lists.digium.com
> > http://lists.digium.com/mailman/listinfo/asterisk-users
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-users
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users