[Asterisk-Users] CAC ADIT600 / T400 config

Sat May 31 20:09:12 MST 2003

On Sat, 2003-05-31 at 21:34, TC wrote:
> Yea looks like i have a issue with t400 spans 2 & 4 :(
> I now can get 2 pretty green lights on span 1 and span 3 &
> on the adit 600 on T1-1 and T1-2 ..and the 2 fxs/3fxo card are all green
> So i plow'd ahead on possible shakey ground ...
> 

Eep...  Bad card maybe?

> But now i dont get any dial tone when i pick up a hand set, the adit 600
> recognizes the off hook & goes amber but * does not see it off hook
> And it has registered the channels
>   == Parsing '/etc/asterisk/zapata.conf': Found
>     -- Registered channel 1, FXO Kewlstart signalling
> 
> just curious what signaling did you need on the ports for * to be a happy
> camper
> with adit fxs cards
> 

I think you may have fxs and fxo reversed.  for the channels bound to
the fxo-8 boards, asterisk has to be set to fxs signalling, and vice
versa.  asterisk needs to be told what signalling to PUT on the line, as
opposed to the signalling the adits expect to GET from the line.  I have
1 fxo-8 board (for the inbound pots lines) and 5 fxs-8 boards (for the
phones), and asterisk has channels 1-8 fxsks and 9-24 fxoks.

> >>After mucking around with it a bit, I was able to get it to sync with the
> >>channel bank as the clock source for the line:
> >>jsci-cbank1> show clock
> >> Primary Master Transmit Clock Source:    Internal
> >>  Secondary Transmit Clock Source:         Slot A DS1 2
> So this means you  have the adit suppling timing to asterisk t1 spans
> so your zaptel looks like this
> span=1,0,0,esf,b8zs
> span=2,0,0,esf,b8zs
> span=3,0,0,esf,b8zs
> span=4,0,0,esf,b8zs
> fxoks=1-24

No, I have:

fxsks=1-8
fxoks=9-24
span=1,1,0,esf,b8zs

> 
> 
> Could post the output of
> print config
> 
> from the adit 600 cli

sure, here ya go:

jsci-cbank1> print config

-------------------------------------------------------------
-Adit 600 configuration file
-Created on 01/09/1999 at 00:48:13 for antkojm1
-This file is valid for the following configuration only:
-
-        CardType
-        --------
-SLOT A    T1x2       SW Version:  1.5.0
-SLOT 1    FXOx8
-SLOT 2    FXSx8
-SLOT 3    FXSx8
-SLOT 4    FXSx8
-SLOT 5    FXSx8
-SLOT 6    FXSx8
-NOTES:
-------------------------------------------------------------

-Turning off verification messages.

set verification off

-Setting local off.

set local off

-Disconnecting all connections.

disconnect a
disconnect 1
disconnect 2
disconnect 3
disconnect 4
disconnect 5
disconnect 6

-Setting IP addresses.

set ethernet ip address 10.109.97.62 255.255.255.0
set ip gateway 10.109.97.1

-Setting the SNMP MIB-II System Group objects.

-Setting slot a.

set a:1 up
set a:1 fdl none
set a:1 lbo 1
set a:1 framing esf
set a:1 id "asterisk-internal trunk"
set a:1 linecode b8zs
set a:1 loopdetect on
set a:1 threshold min15 uas default
set a:1 threshold min15 ses default
set a:1 threshold min15 es default
set a:1 threshold min15 sefs default
set a:1 threshold min15 les default
set a:1 threshold min15 css default
set a:1 threshold min15 bes default
set a:1 threshold min15 dm default
set a:1 threshold min15 lcv default
set a:1 threshold min15 pcv default
set a:1 threshold day uas default
set a:1 threshold day ses default
set a:1 threshold day es default
set a:1 threshold day sefs default
set a:1 threshold day les default
set a:1 threshold day css default
set a:1 threshold day bes default
set a:1 threshold day dm default
set a:1 threshold day lcv default
set a:1 threshold day pcv default
set a:1:1-24 signal ls
set a:1:1-24 type voice
set a:2 down
set a:2 fdl none
set a:2 lbo 1
set a:2 framing esf
set a:2 id "CAC DS1# A:2"
set a:2 linecode b8zs
set a:2 loopdetect on
set a:2 threshold min15 uas default
set a:2 threshold min15 ses default
set a:2 threshold min15 es default
set a:2 threshold min15 sefs default
set a:2 threshold min15 les default
set a:2 threshold min15 css default
set a:2 threshold min15 bes default
set a:2 threshold min15 dm default
set a:2 threshold min15 lcv default
set a:2 threshold min15 pcv default
set a:2 threshold day uas default
set a:2 threshold day ses default
set a:2 threshold day es default
set a:2 threshold day sefs default
set a:2 threshold day les default
set a:2 threshold day css default
set a:2 threshold day bes default
set a:2 threshold day dm default
set a:2 threshold day lcv default
set a:2 threshold day pcv default
set a:2:1-24 signal ls
set a:2:1-24 type voice

-Setting slot 1.

set 1:1-8 signal lscpd
set 1:1-8 txgain 0
set 1:1-8 rxgain 3

-Setting slot 2.

set 2:1-8 signal ls
set 2:1-8 txgain 0
set 2:1-8 rxgain 0
set 2:1-8 linelength short

-Setting slot 3.

set 3:1-8 signal ls
set 3:1-8 txgain 0
set 3:1-8 rxgain 0
set 3:1-8 linelength short

-Setting slot 4.

set 4:1-8 signal ls
set 4:1-8 txgain -3
set 4:1-8 rxgain -6
set 4:1-8 linelength short

-Setting slot 5.

set 5:1-8 signal ls
set 5:1-8 txgain -3
set 5:1-8 rxgain -6
set 5:1-8 linelength short

-Setting slot 6.

set 6:1-8 signal ls
set 6:1-8 txgain -3
set 6:1-8 rxgain -6
set 6:1-8 linelength short

-Setting users.

add user antkojm1
add user guest
set user guest level 3

-Setting network id.

set id "jsci-cbank1"

-Setting primary and secondary clock sources.

set clock1 internal
set clock2 a:2

-Making connections.

connect a:1:1-8 1:1-8
connect a:1:9-16 2:1-8
connect a:1:17-24 3:1-8
connect a:2:1-8 4:1-8
connect a:2:9-16 5:1-8
connect a:2:17-24 6:1-8

-Turning verification on.

set verification on
jsci-cbank1>

> 
> 
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users