[Asterisk-Users] Setting up the E100P

[Martin Pycko]

THat's not it.
in zapata.conf you *also* need to have
signalling=pri_cpe or pri_net

Martin

On Mon, 23 Jun 2003, Michael Bielicki wrote:

> On Monday 23 June 2003 2:58 pm, Anton Yurchenko wrote:
> > Hello,
> >
> > I have an E100P, and in the zaptel.conf I have:
> >
> > span=1,1,0,ccs,hdb4,crc4,yellow
> > fxsks=1-10
> delete the fxsks line and put:
> bchan=1-15,17-31
> dchan=16
> >
> > the light on the card is green( BTW what do all those states of the card
> > that zttool reports YELLO, RED, BLUE ..., is there a doc for zttool?, or
> > for the card?)
> >
> > in the asterisks` zapata.conf I have:
> >
> > [channels]
> > context=default
> > switchtype=euroisdn
> > signalling=fxs_ks
> > usecallerid=yes
> > hidecallerid=no
> > callwaiting=yes
> > callwaitingcallerid=yes
> > threewaycalling=yes
> > transfer=yes
> > cancallforward=yes
> > callreturn=yes
> > echocancel=yes
> > echocancelwhenbridged=yes
> > rxgain=0.0
> > txgain=0.0
> > group=1
> > callgroup=1
> > pickupgroup=1
> >
> > immediate=no
> > callerid="line1"< 238-20-31>
> > channel => 1
> > callerid="line2"< 238-20-31>
> > channel => 2
> >
> >
> > but Asterisk on startup reports that:
> >
> > WARNING[13326]: File chan_zap.c, Line 4173 (ss_thread): CallerID returned
> > with rror on channel 'Zap/1-1'
> > WARNING[14351]: File chan_zap.c, Line 4173 (ss_thread): CallerID returned
> > with rror on channel 'Zap/2-1'
> >
> >
> > and when I call the number that is supposed to terminate there I get
> > busy signal.
> > also in the zttool  I see strange thing, in the bottom portion where
> > there are RxA, RxB .... the 1111111 ( ones) sometimes change into
> > 000000, they go from up to down and if I enable all the channels then
> > firs on the first column then on the second column, in the bottom half
> > of the screen.
> >
> > while if I plug the same E1 into Cisco AS5300, whit this config( just
> > exepts):
> >
> > isdn switch-type primary-net5
> >
> > controller e1 ...
> >  clock source line primary
> >  pri-group timeslots 1-31
> > ...
> >
> > interface Serial0:15
> >  isdn switch-type primary-net5
> >  isdn incoming-voice modem 64
> >
> > Framing is CRC4, Line Code is HDB3, Clock Source is Line ...
> >
> >
> > on Cisco the swithtype is primary-net5 ( my guess its euroisdn ? )
> >
> > anybody could guess what is the problem?
> >
> > The admin that runs the Cisco says that signalyng should be PRI , and there
> > is an option for pri signaling in zapata.conf, but the zaptel,conf doesnt
> > have it and so I`d get up with a mismatch, and zasterisk would not start.
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
>