[asterisk-r2] R2 problem

[William Cardona]

Hi 

Excuse me could you help me with the problem to receive and make calls with a r2, where the all is ok and not show information of the card when run the wanpipemon.

DELL poweregde 310

System.conf
#Sangoma A101 port 1 [slot:4 bus:6 span:1] <wanpipe1>
span=1,1,0,cas,hdb3
cas=1-15:1101
hardhdlc=16
cas=17-31:1101

loadzone=us
defaultzone=us


Chan_dahdi.conf
[trunkgroups]

[channels]

signalling=mfcr2
mfcr2_variant=mx
mfcr2_get_ani_first=no
mfcr2_max_ani=10
mfcr2_max_dnis=4
mfcr2_category=national_subscriber
mfcr2_mfback_timeout=-1
mfcr2_metering_pulse_timeout=-1
mfcr2_logdir=log
mfcr2_logging=all
context=from-pstn

group=1
;echocancel=yes
faxdetect=incoming
restrictcid=yes
hidecallerid=no
channel => 1-15
channel => 17-31

Wanpipe1.conf
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment

[wanpipe1]
CARD_TYPE       = AFT
S514CPU         = A
CommPort        = PRI
AUTO_PCISLOT    = NO
PCISLOT         = 4
PCIBUS          = 6
FE_MEDIA        = E1
FE_LCODE        = HDB3
FE_FRAME        = NCRC4
FE_LINE         = 1
TE_CLOCK        = NORMAL
TE_REF_CLOCK    = 0
TE_SIG_MODE     = CAS
TE_HIGHIMPEDANCE        = NO
TE_RX_SLEVEL    = 430
LBO             = 120OH
FE_TXTRISTATE   = NO
MTU             = 1500
UDPPORT         = 9000
TTL             = 255
IGNORE_FRONT_END        = NO
TDMV_SPAN               = 1
TDMV_DCHAN              = 16
TE_AIS_MAINTENANCE = NO         #NO: defualt  YES: Start port in AIS Blue Alarm and keep line down
                                #wanpipemon -i w1g1 -c Ttx_ais_off to disable AIS maintenance mode
                                                                #wanpipemon -i w1g1 -c Ttx_ais_on to enable AIS maintenance mode
TDMV_HW_DTMF            = YES           # YES: receive dtmf events from hardware
TDMV_HW_FAX_DETECT              = YES           # YES: receive fax 1100hz events from hardware
HWEC_OPERATION_MODE     = OCT_NORMAL    # OCT_NORMAL: echo cancelation enabled with nlp (default)

# OCT_SPEECH: improves software tone detection by disabling NLP (echo possible)

# OCT_NO_ECHO:disables echo cancelation but allows VQE/tone functions.
HWEC_DTMF_REMOVAL       = NO    # NO: default  YES: remove dtmf out of incoming media (must have hwdtmf enabled)
HWEC_NOISE_REDUCTION    = NO    # NO: default  YES: reduces noise on the line - could break fax
HWEC_ACUSTIC_ECHO       = NO    # NO: default  YES: enables acustic echo cancelation
HWEC_NLP_DISABLE        = NO    # NO: default  YES: guarantees software tone detection (possible echo)
HWEC_TX_AUTO_GAIN       = 0     # 0: disable   -40-0: default tx audio level to be maintained (-20 default)

Wanrouter hwprobe
-------------------------------
| Wanpipe Hardware Probe Info |
-------------------------------
1 . AFT-A101-SH : SLOT=4 : BUS=6 : IRQ=15 : CPU=A : PORT=1 : HWEC=32 : V=37

Card Cnt: A101-2=1

Cat /proc/interrups
[root at SRVCALL2 ~]# cat /proc/interrupts
           CPU0       CPU1       CPU2       CPU3
  0:        245          0          0    1067168    IO-APIC-edge  timer
  8:          0          0          3          0    IO-APIC-edge  rtc
  9:          0          0          0          0   IO-APIC-level  acpi
 58:      14582          0          0          0       PCI-MSI-X  eth0-0
 66:       4158          0          0          0       PCI-MSI-X  eth0-1
 74:       6797          0          0          0       PCI-MSI-X  eth0-2
 82:       3600          0          0          0       PCI-MSI-X  eth0-3
 90:       2448          0          0          0       PCI-MSI-X  eth0-4
 98:          1          0          0          0       PCI-MSI-X  cnic
169:          0          0    1025706          0   IO-APIC-level  wanpipe1
217:          0        173          0          0   IO-APIC-level  ehci_hcd:usb1,             ehci_hcd:usb2
225:          0          0       9181          0   IO-APIC-level  ata_piix
233:          0          0      11044          0   IO-APIC-level  ata_piix
NMI:          0          0          0          0
LOC:    1067151    1067170    1067167    1067169
ERR:          0
MIS:          0


Wanrouter Status
Devices currently active:
        wanpipe1


Wanpipe Config:

Device name | Protocol Map | Adapter  | IRQ | Slot/IO | If's | CLK | Baud rate |
wanpipe1    | N/A          | A101/1D/A102/2D/4/4D/8| 169 | 4       | 1    | N/A | 0         |

Wanrouter Status:

Device name | Protocol | Station | Status        |
wanpipe1    | AFT TE1  | N/A     | Connected     |



Atte
 


   William A. Cardona
"Todo lo Puedo en Cristo que me Fortalece"
Honduras, CentralAmerica
       504 9834 9127
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.digium.com/pipermail/asterisk-r2/attachments/20120509/013e0d2a/attachment.htm>