[asterisk-r2] asterisk-r2 Digest, Vol 5, Issue 13
Gabriel Monsalvo
gabriel at arlab.com.ar
Thu Jan 15 12:50:50 CST 2009
Hi moy!
I enabled the callfiles option, this is the callfile for a dial call,
[15:43:21:977] [Thread: 3078126480] [Chan 1] - Call started at Thu Jan
15 15:43:21 2009 on chan 1
[15:43:21:977] [Thread: 3078126480] [Chan 1] - CAS Tx >> [SEIZE] 0x00
[15:43:21:977] [Thread: 3078126480] [Chan 1] - CAS Raw Tx >> 0x01
[15:43:22:006] [Thread: 3078126480] [Chan 1] - Bits changed from 0x08 to
0x0C
[15:43:22:006] [Thread: 3078126480] [Chan 1] - CAS Rx << [SEIZE ACK] 0x0C
[15:43:22:006] [Thread: 3078126480] [Chan 1] - Attempting to cancel
timer timer 2
[15:43:22:006] [Thread: 3078126480] [Chan 1] - timer id 2 found,
cancelling it now
[15:43:22:006] [Thread: 3078126480] [Chan 1] - Sending DNIS digit 1
[15:43:22:006] [Thread: 3078126480] [Chan 1] - MF Tx >> 1 [ON]
[15:43:42:348] [Thread: 3078126480] [Chan 1] - Attempting to cancel
timer timer 0
[15:43:42:348] [Thread: 3078126480] [Chan 1] - Cannot cancel timer 0
[15:43:42:348] [Thread: 3078126480] [Chan 1] - CAS Tx >> [CLEAR FORWARD]
0x08
[15:43:42:348] [Thread: 3078126480] [Chan 1] - CAS Raw Tx >> 0x09
[15:43:42:408] [Thread: 3081071504] [Chan 1] - Alarm Cleared
[15:43:42:662] [Thread: 3081071504] [Chan 1] - Bits changed from 0x0C to
0x08
[15:43:42:662] [Thread: 3081071504] [Chan 1] - CAS Rx << [IDLE] 0x08
[15:43:42:662] [Thread: 3081071504] [Chan 1] - Call ended
[15:43:42:662] [Thread: 3081071504] [Chan 1] - Attempting to cancel
timer timer 0
[15:43:42:662] [Thread: 3081071504] [Chan 1] - Cannot cancel timer 0
and this is for incoming call to E1 line,
[15:48:30:547] [Thread: 3081071504] [Chan 2] - Call started at Thu Jan
15 15:48:30 2009 on chan 2
[15:48:30:547] [Thread: 3081071504] [Chan 2] - CAS Tx >> [SEIZE ACK] 0x0C
[15:48:30:547] [Thread: 3081071504] [Chan 2] - CAS Raw Tx >> 0x0D
[15:48:30:726] [Thread: 3081071504] [Chan 2] - MF Rx << 6 [ON]
[15:48:30:726] [Thread: 3081071504] [Chan 2] - Attempting to cancel
timer timer 0
[15:48:30:726] [Thread: 3081071504] [Chan 2] - Cannot cancel timer 0
[15:48:30:726] [Thread: 3081071504] [Chan 2] - Getting DNIS digit 6
[15:48:30:726] [Thread: 3081071504] [Chan 2] - DNIS so far: 6, expected
length: 4
[15:48:30:726] [Thread: 3081071504] [Chan 2] - Requesting next DNIS with
signal 0x31.
[15:48:30:726] [Thread: 3081071504] [Chan 2] - MF Tx >> 1 [ON]
[15:48:30:746] [Thread: 3081071504] [Chan 2] - MF Rx << 6 [OFF]
[15:48:30:746] [Thread: 3081071504] [Chan 2] - MF Tx >> 1 [OFF]
[15:48:35:726] [Thread: 3081071504] [Chan 2] - Attempting to cancel
timer timer 2
[15:48:35:726] [Thread: 3081071504] [Chan 2] - timer id 2 found,
cancelling it now
[15:48:35:726] [Thread: 3081071504] [Chan 2] - calling timer callback
[15:48:35:726] [Thread: 3081071504] [Chan 2] - MF cycle timed out, no
more DNIS
[15:48:35:726] [Thread: 3081071504] [Chan 2] - MF Tx >> 5 [ON]
[15:48:35:886] [Thread: 3081071504] [Chan 2] - Attempting to cancel
timer timer 3
[15:48:35:886] [Thread: 3081071504] [Chan 2] - timer id 3 found,
cancelling it now
[15:48:35:886] [Thread: 3081071504] [Chan 2] - calling timer callback
[15:48:35:886] [Thread: 3081071504] [Chan 2] - MF Tx >> 5 [OFF]
[15:48:49:939] [Thread: 3081071504] [Chan 2] - Bits changed from 0x00 to
0x08
[15:48:49:939] [Thread: 3081071504] [Chan 2] - CAS Rx << [CLEAR FORWARD]
0x08
[15:48:49:939] [Thread: 3081071504] [Chan 2] - Far end disconnected.
Reason: Normal Clearing
[15:48:49:939] [Thread: 3081071504] [Chan 2] - Call ended
[15:48:49:939] [Thread: 3081071504] [Chan 2] - Attempting to cancel
timer timer 0
[15:48:49:939] [Thread: 3081071504] [Chan 2] - Cannot cancel timer 0
in both cases does not hear anything.
Thanks in advance,
Gabriel Monsalvo.
> Send asterisk-r2 mailing list submissions to
> asterisk-r2 at lists.digium.com
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://lists.digium.com/mailman/listinfo/asterisk-r2
> or, via email, send a message with subject or body 'help' to
> asterisk-r2-request at lists.digium.com
>
> You can reach the person managing the list at
> asterisk-r2-owner at lists.digium.com
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of asterisk-r2 digest..."
>
>
> Today's Topics:
>
> 1. Re: Problem using patch for 1.4.18 (Carlos Chavez)
> 2. Re: asterisk-r2 Digest, Vol 5, Issue 12 (Gabriel Monsalvo)
> 3. help,dahdi_scan,alarm=red (Qian Ma)
> 4. Re: help,dahdi_scan,alarm=red (Melcon Moraes)
> 5. Re: asterisk-r2 Digest, Vol 5, Issue 12 (Moises Silva)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Wed, 14 Jan 2009 15:27:44 -0600
> From: Carlos Chavez <cursor at telecomabmex.com>
> Subject: Re: [asterisk-r2] Problem using patch for 1.4.18
> To: asterisk-r2 at lists.digium.com
> Message-ID: <1231968464.3400.4.camel at cursor.telecomabmex.com>
> Content-Type: text/plain; charset="utf-8"
>
> Ok. It now works. I only get this warning when compiling:
>
> chan_zap.c: In function ?zt_r2_on_hardware_alarm?:
> chan_zap.c:974: warning: unused variable ?res?
>
> Any concerns about that?
>
> On Wed, 2009-01-14 at 12:42 -0500, Moises Silva wrote:
>
>> I installed from source, and now that you mention it, I think I had
>> the same problem you have and that's why I installed 2.60.
>>
>> This is a direct link: http://ftp.gnu.org/gnu/autoconf/autoconf-2.60.tar.bz2
>>
>> And this is the official web page: http://www.gnu.org/software/autoconf/
>>
>>
>> On Wed, Jan 14, 2009 at 12:38 PM, Carlos Chavez <cursor at telecomabmex.com> wrote:
>>
>>> Ok. Where did you get autoconf 2.60 for fedora 10? The version that
>>> installs by default is 2.63 which is the one I used.
>>>
>>> On Wed, 2009-01-14 at 12:34 -0500, Moises Silva wrote:
>>>
>>>> I did not quite understand what you mean about the fedora versions.
>>>>
>>>> I have Fedora 10 installed on my laptop and installed autoconf-2.60
>>>> and the ./bootstrap.sh script runs without problems. This definitely
>>>> is a problem with the versions of autotools.
>>>>
>>>> Where did you run the ./bootstrap.sh script and under which autoconf version?
>>>>
>>>> On Wed, Jan 14, 2009 at 12:26 PM, Carlos Chavez <cursor at telecomabmex.com> wrote:
>>>>
>>>>> Yes, this is what I get when I run bootstrap.sh in the asterisk
>>>>> directory after applying the patch:
>>>>> [root at cursor asterisk-1.4.18]# ./bootstrap.sh
>>>>> Generating the configure script ...
>>>>> configure.ac:21: warning: AC_COMPILE_IFELSE was called before
>>>>> AC_USE_SYSTEM_EXTENSIONS
>>>>> ../../lib/autoconf/specific.m4:386: AC_USE_SYSTEM_EXTENSIONS is expanded
>>>>> from...
>>>>> configure.ac:21: the top level
>>>>> configure.ac:21: warning: AC_RUN_IFELSE was called before
>>>>> AC_USE_SYSTEM_EXTENSIONS
>>>>> configure.ac:124: warning: AC_CACHE_VAL(GNU_MAKE, ...): suspicious
>>>>> cache-id, must contain _cv_ to be cached
>>>>> ../../lib/autoconf/general.m4:1974: AC_CACHE_VAL is expanded from...
>>>>> ../../lib/autoconf/general.m4:1994: AC_CACHE_CHECK is expanded from...
>>>>> acinclude.m4:101: AST_CHECK_GNU_MAKE is expanded from...
>>>>> configure.ac:124: the top level
>>>>> configure:6379: error: possibly undefined macro:
>>>>> _AC_PATH_PROG_FEATURE_CHECK
>>>>> If this token and others are legitimate, please use
>>>>> m4_pattern_allow.
>>>>> See the Autoconf documentation.
>>>>> configure:6380: error: possibly undefined macro:
>>>>> _AC_FEATURE_CHECK_LENGTH
>>>>> configure.ac:21: warning: AC_COMPILE_IFELSE was called before
>>>>> AC_USE_SYSTEM_EXTENSIONS
>>>>> ../../lib/autoconf/specific.m4:386: AC_USE_SYSTEM_EXTENSIONS is expanded
>>>>> from...
>>>>> configure.ac:21: the top level
>>>>> configure.ac:21: warning: AC_RUN_IFELSE was called before
>>>>> AC_USE_SYSTEM_EXTENSIONS
>>>>> configure.ac:124: warning: AC_CACHE_VAL(GNU_MAKE, ...): suspicious
>>>>> cache-id, must contain _cv_ to be cached
>>>>> ../../lib/autoconf/general.m4:1974: AC_CACHE_VAL is expanded from...
>>>>> ../../lib/autoconf/general.m4:1994: AC_CACHE_CHECK is expanded from...
>>>>> acinclude.m4:101: AST_CHECK_GNU_MAKE is expanded from...
>>>>> configure.ac:124: the top level
>>>>>
>>>>>
>>>>>
>>>>> On Wed, 2009-01-14 at 12:24 -0500, Moises Silva wrote:
>>>>>
>>>>>> did you run the ./bootstrap.sh script after applying the patch?
>>>>>>
>>>>>> On Wed, Jan 14, 2009 at 12:22 PM, Carlos Chavez <cursor at telecomabmex.com> wrote:
>>>>>>
>>>>>>> I am trying to use the patch for Asterisk 1.4.18, it applies with now
>>>>>>> errors or warnings. I do get several warnings when running bootstrap.sh
>>>>>>> but no errors. When running ./configure I get the following error:
>>>>>>>
>>>>>>> checking for a sed that does not truncate output... ./configure: line
>>>>>>> 6379: syntax error near unexpected token `SED,'
>>>>>>> ./configure: line 6379: ` _AC_PATH_PROG_FEATURE_CHECK(SED, sed
>>>>>>> gsed,'
>>>>>>>
>>>>>>> I do not know if this has something to do that I applied the patch on a
>>>>>>> Fedora 10 system because I do not have autoconf 2.60 on the machine I am
>>>>>>> trying to compile asterisk (Fedora Core 5).
>>>>>>>
>>>>>>>
>>>>>>> --
>>>>>>> Telecomunicaciones Abiertas de M?xico S.A. de C.V.
>>>>>>> Carlos Ch?vez Prats
>>>>>>> Director de Tecnolog?a
>>>>>>> +52-55-91169161 ext 2001
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> --Bandwidth and Colocation Provided by http://www.api-digital.com--
>>>>>>>
>>>>>>> asterisk-r2 mailing list
>>>>>>> To UNSUBSCRIBE or update options visit:
>>>>>>> http://lists.digium.com/mailman/listinfo/asterisk-r2
>>>>>>>
>>>>>>>
>>>>>>
>>>>>>
>>>>> --
>>>>> Telecomunicaciones Abiertas de M?xico S.A. de C.V.
>>>>> Carlos Ch?vez Prats
>>>>> Director de Tecnolog?a
>>>>> +52-55-91169161 ext 2001
>>>>>
>>>>> _______________________________________________
>>>>> --Bandwidth and Colocation Provided by http://www.api-digital.com--
>>>>>
>>>>> asterisk-r2 mailing list
>>>>> To UNSUBSCRIBE or update options visit:
>>>>> http://lists.digium.com/mailman/listinfo/asterisk-r2
>>>>>
>>>>>
>>>>
>>>> --
>>>> "I do not agree with what you have to say, but I'll defend to the
>>>> death your right to say it." Voltaire
>>>>
>>>> _______________________________________________
>>>> --Bandwidth and Colocation Provided by http://www.api-digital.com--
>>>>
>>>> asterisk-r2 mailing list
>>>> To UNSUBSCRIBE or update options visit:
>>>> http://lists.digium.com/mailman/listinfo/asterisk-r2
>>>>
>>> --
>>> Telecomunicaciones Abiertas de M?xico S.A. de C.V.
>>> Carlos Ch?vez Prats
>>> Director de Tecnolog?a
>>> +52-55-91169161 ext 2001
>>>
>>> _______________________________________________
>>> --Bandwidth and Colocation Provided by http://www.api-digital.com--
>>>
>>> asterisk-r2 mailing list
>>> To UNSUBSCRIBE or update options visit:
>>> http://lists.digium.com/mailman/listinfo/asterisk-r2
>>>
>>>
>>
>>
More information about the asterisk-r2
mailing list