[asterisk-r2] Asterisk R2 configuration

Thu Nov 20 15:59:15 CST 2008

ok, now ive tested with the crossover and got both spans on green, then 
talked to my telco and now they checked the configuration on their side 
and now i get 1 green and 1 yellow/red  should i change anything on my 
cofiguration or just should wait for them to figure out what the problem is?

Camilo

Moises Silva wrote:
> correct ... that should give you a solid green in zttool or dahdi_tool
> 
> On Thu, Nov 20, 2008 at 2:48 PM, Camilo Quelquejeu <camilo at cabimax.com> wrote:
>> and to test it i should connect one side to one of the two ports in my
>> server and the other side to the second correct?
>>
>> Camilo
>>
>> Moises Silva wrote:
>>> This is more graphic: http://www.moythreads.com/unicall/e1_crossover.html
>>>
>>> On Thu, Nov 20, 2008 at 12:19 PM, Alexis Gavidia <agavidia at iptelven.com> wrote:
>>>> RJ-45 pin numbering
>>>>
>>>>
>>>>
>>>> 1 -> RRING
>>>> 2 -> RTIP
>>>> 4 -> TRING
>>>> 5 -> TTIP
>>>>
>>>> To make a loop join 1 with 4 and 2 with 5.
>>>>
>>>>
>>>> On Thu, Nov 20, 2008 at 1:42 PM, Camilo Quelquejeu <camilo at cabimax.com>
>>>> wrote:
>>>>> and i should connect the cross over cable from one E1 port to the other?
>>>>> to create a loop correct? on that same note will any cross over cable
>>>>> work of i need to have that specific crossover cable with the diagram
>>>>> moy provided?
>>>>>
>>>>> Camilo
>>>>>
>>>>> Melcon Moraes wrote:
>>>>>> Buying Moy's advice on crossover E1 cable should help you. That would
>>>>>> be a nice starting point.
>>>>>>
>>>>>> -MM
>>>>>>
>>>>>> On Tue, Nov 18, 2008 at 2:17 PM, Camilo Quelquejeu <camilo at cabimax.com>
>>>>>> wrote:
>>>>>>> and the only way to check that is with the cable right?
>>>>>>>
>>>>>>> Camilo
>>>>>>>
>>>>>>> Moises Silva wrote:
>>>>>>>> unicall has nothing to do with the red alarms.
>>>>>>>>
>>>>>>>> check your installation? yes, when you get rid of the red alarms. The
>>>>>>>> first thing is to get rid of the red alarms, and red alarms mean you
>>>>>>>> connected something physically wrong or you configured the zaptel.conf
>>>>>>>> wrong for the type of link provided.
>>>>>>>>
>>>>>>>> On Tue, Nov 18, 2008 at 9:24 AM, Camilo Quelquejeu
>>>>>>>> <camilo at cabimax.com> wrote:
>>>>>>>>> Is there any chance i have the compilation and instalation of the
>>>>>>>>> unicall wrong, hence the red alarms? is there any way i can check my
>>>>>>>>> instalation?
>>>>>>>>>
>>>>>>>>> Camilo
>>>>>>>>>
>>>>>>>>> Moises Silva wrote:
>>>>>>>>>> I don't see anything wrong with your config, but looks suspicious to
>>>>>>>>>> me that you are using span=2,0,0
>>>>>>>>>>
>>>>>>>>>> Are you use you want span 2 to be the master?
>>>>>>>>>>
>>>>>>>>>> In any case, you can create a E1 cross-over cable to verify your own
>>>>>>>>>> configuration without the telco. check this out:
>>>>>>>>>> http://www.moythreads.com/unicall/e1_crossover.html
>>>>>>>>>>
>>>>>>>>>> That way you will discard your configuration and can call the telco
>>>>>>>>>> to
>>>>>>>>>> ask why your link is down.
>>>>>>>>>>
>>>>>>>>>> On Thu, Oct 30, 2008 at 1:47 PM, Camilo Quelquejeu
>>>>>>>>>> <camilo at cabimax.com> wrote:
>>>>>>>>>>> the zaptel.conf goes like this
>>>>>>>>>>> # Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER)
>>>>>>>>>>> HDB3/CCS/CRC4 RED
>>>>>>>>>>> span=1,1,0,cas,hdb3
>>>>>>>>>>> cas=1-15:1101
>>>>>>>>>>> cas=17-31:1101
>>>>>>>>>>> #
>>>>>>>>>>> span=2,0,0,cas,hdb3
>>>>>>>>>>> cas=32-46:1101
>>>>>>>>>>> cas=48-62:1101
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> # Global data
>>>>>>>>>>>
>>>>>>>>>>> loadzone        = br
>>>>>>>>>>> defaultzone     = br
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> and the ztcfg -v  goes like this
>>>>>>>>>>>
>>>>>>>>>>> SPAN 1: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
>>>>>>>>>>> SPAN 2: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
>>>>>>>>>>>
>>>>>>>>>>> 60 channels to configure.
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> thanks in advanced for the help
>>>>>>>>>>>
>>>>>>>>>>> Camilo
>>>>>>>>>>>
>>>>>>>>>>> Moises Silva wrote:
>>>>>>>>>>>> It could be caused by the moon :) who knows, without showing your
>>>>>>>>>>>> zaptel.conf and pastebin of the output of ztcfg -vv we cannot try
>>>>>>>>>>>> to
>>>>>>>>>>>> answer.
>>>>>>>>>>>>
>>>>>>>>>>>> On Thu, Oct 30, 2008 at 11:20 AM, Camilo Quelquejeu
>>>>>>>>>>>> <camilo at cabimax.com>
>>>>>>>>>>>> wrote:
>>>>>>>>>>>>> I installed, compiled and configured the astunicall, and when i
>>>>>>>>>>>>> use the
>>>>>>>>>>>>> ztcfg -v command, it tells me there are 60 channels to be
>>>>>>>>>>>>> configured and
>>>>>>>>>>>>> the zttool shows the card with a red alarm, what could be the
>>>>>>>>>>>>> cause of
>>>>>>>>>>>>> this? does anyone know how to configure the extensions.conf so i
>>>>>>>>>>>>> can use
>>>>>>>>>>>>> the unicall channels to receive calls in El salvador?
>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>> --
>>>>>>>>>>>>> Camilo Quelquejeu
>>>>>>>>>>>>> Chief IT  |  Cabimax, S.A.
>>>>>>>>>>>>> camilo at cabimax.com  Tel: 302-7424
>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>> _______________________________________________
>>>>>>>>>>>>> --Bandwidth and Colocation Provided by
>>>>>>>>>>>>> http://www.api-digital.com--
>>>>>>>>>>>>>
>>>>>>>>>>>>> asterisk-r2 mailing list
>>>>>>>>>>>>> To UNSUBSCRIBE or update options visit:
>>>>>>>>>>>>>  http://lists.digium.com/mailman/listinfo/asterisk-r2
>>>>>>>>>>>>>
>>>>>>>>>>> --
>>>>>>>>>>> Camilo Quelquejeu
>>>>>>>>>>> Chief IT  |  Cabimax, S.A.
>>>>>>>>>>> camilo at cabimax.com  Tel: 302-7424
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>> --
>>>>>>>>> Camilo Quelquejeu
>>>>>>>>> Chief IT  |  Cabimax, S.A.
>>>>>>>>> camilo at cabimax.com  Tel: 302-7424
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> _______________________________________________
>>>>>>>>> --Bandwidth and Colocation Provided by http://www.api-digital.com--
>>>>>>>>>
>>>>>>>>> asterisk-r2 mailing list
>>>>>>>>> To UNSUBSCRIBE or update options visit:
>>>>>>>>>   http://lists.digium.com/mailman/listinfo/asterisk-r2
>>>>>>>>>
>>>>>>> --
>>>>>>> Camilo Quelquejeu
>>>>>>> Chief IT  |  Cabimax, S.A.
>>>>>>> camilo at cabimax.com  Tel: 302-7424
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> --Bandwidth and Colocation Provided by http://www.api-digital.com--
>>>>>>>
>>>>>>> asterisk-r2 mailing list
>>>>>>> To UNSUBSCRIBE or update options visit:
>>>>>>>   http://lists.digium.com/mailman/listinfo/asterisk-r2
>>>>>>>
>>>>> --
>>>>> Camilo Quelquejeu
>>>>> Chief IT  |  Cabimax, S.A.
>>>>> camilo at cabimax.com  Tel: 302-7424
>>>>>
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> --Bandwidth and Colocation Provided by http://www.api-digital.com--
>>>>>
>>>>> asterisk-r2 mailing list
>>>>> To UNSUBSCRIBE or update options visit:
>>>>>   http://lists.digium.com/mailman/listinfo/asterisk-r2
>>>> _______________________________________________
>>>> --Bandwidth and Colocation Provided by http://www.api-digital.com--
>>>>
>>>> asterisk-r2 mailing list
>>>> To UNSUBSCRIBE or update options visit:
>>>>   http://lists.digium.com/mailman/listinfo/asterisk-r2
>>>>
>>>
>>>
>> --
>> Camilo Quelquejeu
>> Chief IT  |  Cabimax, S.A.
>> camilo at cabimax.com  Tel: 302-7424
>>
>>
>>
>> _______________________________________________
>> --Bandwidth and Colocation Provided by http://www.api-digital.com--
>>
>> asterisk-r2 mailing list
>> To UNSUBSCRIBE or update options visit:
>>   http://lists.digium.com/mailman/listinfo/asterisk-r2
>>
> 
> 
> 

-- 
Camilo Quelquejeu
Chief IT  |  Cabimax, S.A.
camilo at cabimax.com  Tel: 302-7424