[asterisk-users] B410P and Patton smartnode : any success ?

[Olivier]

Hi,

1. Has someone met any success at all, connecting a Digium B410P to a Patton
Smartnode 4638 (with latest 5.3 firmware) ?


2. If positive, then, which signalling was used on both sides ?

My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines,
from a B410P-enabled asterisk box.
In my testings, I can see channel is respectively up (with patton web server
status page) and OK (with dahdi_tool) from both sides but I can't dial a
single call ("Unable to create DAHDI for unknown reason...") from asterisk
to patton.

In my setup, my main settings are :
Smartnode side:     dss1,Net,pp,q931,q921
B410P side:
euroisdn,bri_cpe,span=1,1,0,ccs,ami,bchan=1-2,hardhdlc=3

Both devices lights are green but I think this only means layer1 diag is OK.
Looking at http://en.wikipedia.org/wiki/Digital_Subscriber_System_No._1, I
would say DSS1 and EuroISDN are the same (but that doesn't mean both
implementations are compliant to each other).

The mostly troubling thing is :
CLI> pri show spans
CLI>

Though with dmesg :
[ 3923.671739] dahdi: Version: SVN-trunk-r7640M
[ 3923.683743] wcb4xxp 0000:01:0a.0: probe called for b4xx...
[ 3923.683743] ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 21 (level, low) ->
IRQ 21
[ 3923.683743] wcb4xxp 0000:01:0a.0: Identified Wildcard B410P (controller
rev 1) at 0001dff0, IRQ 21
[ 3923.683743] wcb4xxp 0000:01:0a.0: VPM 0/1 init: chip ver 33
[ 3923.692430] wcb4xxp 0000:01:0a.0: VPM 1/1 init: chip ver 33
[ 3923.704465] wcb4xxp 0000:01:0a.0: Hardware echo cancellation enabled.
[ 3923.704561] wcb4xxp 0000:01:0a.0: Port 1: TE mode
[ 3923.708484] wcb4xxp 0000:01:0a.0: Port 2: TE mode
[ 3923.708484] wcb4xxp 0000:01:0a.0: Port 3: TE mode
[ 3923.708484] wcb4xxp 0000:01:0a.0: Port 4: TE mode
[ 3923.708484] wcb4xxp 0000:01:0a.0: Did not do the highestorder stuff
[ 3923.794449] dahdi_echocan_oslec: Registered echo canceler 'OSLEC'
[ 3923.795577] dahdi: Registered tone zone 2 (France)
[ 3923.811320] wcb4xxp 0000:01:0a.0: new card sync source: port 1

/var/log/asterisk/full does show any warning or error related to Dahdi/PRI.

# cat /proc/interrupts
           CPU0       CPU1
  0:         84          0   IO-APIC-edge      timer
...
 21:    4030670          0   IO-APIC-fasteoi   b4xxp


Regards
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100509/b89d9f9c/attachment.htm