[asterisk-users] Audiocodes MP-114 2FXO/2FXS help registering with Asterisk

[Jonathan Thurman]

The best document is the two page quick start guide that came in the  
box. You want 5.6, and 5.8 should be out soon if you are an early  
adopter.

-Jonathan

Sent from a mobile device.

On Dec 27, 2009, at 9:02 AM, Joseph <syscon780 at gmail.com> wrote:

> What what everybody says, it is a good hardware but configuration  
> samples are not easy to find and going through 500page manual is not  
> easy.
> What they are missing is short configuration guide with samples for  
> specific software like asterisk.
> My software version is 5.40A I see early next week what is the  
> latest available.
>
> On 12/27/09 07:56, Jonathan Thurman wrote:
>> The web interface is a bit confusing at first.  Here are some of the
>> steps that I remember off hand.  Change as little as possible, makes
>> it easier to troubleshoot later.
>
> I did not change much and trying to register just one line first,  
> but is not easy all I'm getting is:
> chan_sip.c:15593 handle_request_register: Registration from '<sip: 
> 369 at 10.0.0.109>' failed for '10.0.0.157' - Wrong password
>
> 369 is my extension, 10.0.0.109 is my Asterisk server, 10.0.0.157 is  
> AudioCodes IP
>
>>
>> Get the latest code from your vendor (5.6 is what I run)
>>
>> Configure the proxy to register with
>> Configuration -> Protocol Config -> Protocol Def -> Proxy and  
>> Registration
>>   - Enable registration
>>   - Set the registration per endpoint
>
> So I have
> Use Default Proxy: Yes
> Proxy Set Table: ==> What did you enter here (I enter: 10.0.0.109  
> UDP; do I need to set: Enable Proxy Keep Alive?)
>
> Proxy Name: 10.0.0.109
>
> The below two settings (what to put in there, setting from sip.conf:  
> eg.: but which one?
> Registrar Name
> Registrar IP Address
>
> Under:
> Gateway Name (I entered asterisk IP) 10.0.0.109
>
> Again below is:
> User Name
> Password
> Not sure what to put in above.
>
>>
>> Configure your call routing
>> Configuration -> Protocol Config -> Routing Tables -> IP to Trunk  
>> Group
>
> Is above sections for routing calls to asterisk?
>
>>
>> If you send a prefix for outgoing calls, you will need to configure
>> that in the manipulation table too
>> Configuration -> Protocol Config -> Manipulation tables -> Dest
>> number IP to Tel
>
> No, I don't use prefixes they are dropped by asterisk; so I  
> configured single stage dialing under:
> Advanced Applications -> FXO Settings -> Dialing Mode
>
>>
>> Configure authentication
>> Configuration -> Protocol Config -> Endpoint settings ->  
>> Authentication
>
> Here I entered authentication from one of my sip.conf entry: [369]
> [369] ; outgoing/incoming call on fxs port
> type=friend
> host=dynamic
> context=internal
> secret=523
> username=369
> mailbox=369
> ;dtmfmode=rfc2833
> ;dtmfmode=inband
> disallow=all
> allow=ulaw
> allow=alaw
> canreinvite=yes
> nat=no
> callgroup=1
> pickupgroup=1
>
>>
>> Now the part that took me a while to find...
>>
>> Configure the Channel to phone number mapping:
>> Configuration -> Protocol Config -> Endpoint  Number -> EndPoint  
>> Phone Number
>>
>> Configure the Hunt group settings
>> Configuration -> Protocol Config -> Hunt/IP Group -> Hunt group  
>> settings
>>
>>
>> Hope that helps.  These are great devices, once you figure out how to
>> get them configured...
>>
>> -Jonathan
>
> I need to find out from the manual what these setting do.
> I was hoping to find some setting reference on Wiki but there are  
> none :-/ it seems to me the device is not very popular among  
> asterisk users, if it was
> somebody would create detailed configuration for asterisk.
>
> --
> Joseph
>
> _______________________________________________
> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users