[asterisk-users] B410P install

[Chris Curtis]

We are trying to get our first B410P installation working but unable to get
any L1 or L2 links.

Connecting  3 ports to BRI lines via S/T interfaces on telco provided NT
equipment.

 

Using Debian etch 2.6.18-6

 

Ports are configured as TE

Have tried both PTP and PTMP modes

 

All 4 red lights are flashing. When we connect the ISDN cable, NOTHING
HAPPENS and unable to receive or make calls.

Have tried both Cross-over and straight through cables.

Telco is adamant the ISDN lines are working fine.

 

# misdn-init scan

[OK] found the following devices:

card=1,0x4

 

# misdnportinfo

 

Port  1: TE-mode BRI S/T interface line (for phone lines)

 -> Interface is Poin-To-Point.

 -> Protocol: DSS1 (Euro ISDN)

 -> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib.

 -> childcnt: 2

 * Port NOT useable for PBX (maybe there is already a PBX running?)

 

.... and so on

 

The driver appears to load OK, except for some entries highlighted below.

Syslog from starting the driver:

 

May 23 22:27:22 cats kernel: Modular ISDN Stack core version (1_1_7_2)
revision ($Revision: 1.40 $)

May 23 22:27:22 cats kernel: mISDNd: kernel daemon started
(current:c8ac7030)

May 23 22:27:22 cats kernel: mISDNd: test event done

May 23 22:27:22 cats kernel: ISDN L1 driver version 1.20

May 23 22:27:22 cats kernel: ISDN L2 driver version 1.32

May 23 22:27:22 cats kernel: mISDN: DSS1 Rev. 1.47

May 23 22:27:22 cats kernel: mISDN Capi 2.0 driver file version 1.21

May 23 22:27:23 cats kernel: mISDN: HFC-multi driver Rev. 1.68

May 23 22:27:23 cats kernel: HFC-multi: card manufacturer: 'Cologne Chip AG'
card name: 'HFC-4S Digium Card' clock: normal

May 23 22:27:23 cats kernel: PCI: Enabling device 0000:00:0c.0 (0000 ->
0003)

May 23 22:27:23 cats kernel: ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17
(level, low) -> IRQ 193

May 23 22:27:23 cats kernel: HFC-4S#1: defined at IOBASE 0xff00 IRQ 193 HZ
250 leds-type 2

May 23 22:27:23 cats kernel: HFC_multi: resetting HFC with chip ID=0xc
revision=1

May 23 22:27:23 cats kernel: Setting GPIOs

May 23 22:27:23 cats kernel: calling vpm_init

May 23 22:27:23 cats kernel: VPM: Chip 0: ver 33

May 23 22:27:23 cats kernel: VPM: A-law mode

May 23 22:27:23 cats kernel: VPM reg 0x20 is 11

May 23 22:27:23 cats kernel: NLP Thresh is set to 2 (0x2)

May 23 22:27:23 cats kernel: VPM: A-law mode

May 23 22:27:23 cats kernel: VPM reg 0x20 is 11

May 23 22:27:23 cats kernel: NLP Thresh is set to 2 (0x2)

May 23 22:27:23 cats kernel: hfcpci_probe: DIPs(0x90) jumpers(0x0)

May 23 22:27:23 cats kernel: register_layer: register_sysfs failed -17
st(00000100) inst(40000100)     ç======= Bothered by these entries

May 23 22:27:23 cats kernel: register_layer: register_sysfs failed -17
st(00000200) inst(40000200)

May 23 22:27:23 cats kernel: register_layer: register_sysfs failed -17
st(00000300) inst(40000300)

May 23 22:27:24 cats kernel: register_layer: register_sysfs failed -17
st(00000400) inst(40000400)

May 23 22:27:24 cats kernel: 1 devices registered

May 23 22:27:24 cats kernel: mISDN_dsp: Audio DSP  Rev. 1.29 (debug=0x0)
EchoCancellor MG2 dtmfthreshold(100)

May 23 22:27:24 cats kernel: mISDN_dsp: DSP clocks every 128 samples. This
equals 4 jiffies.

 

CLI> misdn show stacks

BEGIN STACK_LIST:

  * Port 1 Type TE Prot. PTP L2Link DOWN L1Link:DOWN Blocked:0  Debug:0

  * Port 2 Type TE Prot. PTP L2Link DOWN L1Link:DOWN Blocked:0  Debug:0

  * Port 3 Type TE Prot. PTP L2Link DOWN L1Link:DOWN Blocked:0  Debug:0

CLI>

 

As usual its rather urgent to get it running. If anyone can provide
suggestions ,I’d be very grateful.

 

Chris

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080523/21c45fbe/attachment.htm