[asterisk-users] capi installation problem

[Armin Schindler]

I think you are mixing something here. The FritzCard is not a "B1", so you 
don't need the b1 modules, the firmware and the /etc/capi.conf.

You can either use the FritzCard driver (binary modules from AVM), or you 
use mISDN (which is also already loaded according to your lsmod).

When using mISDN, you can either use the mISDN-CAPI to really provide a CAPI
interface, or just don't use CAPI and use chan_misdn instead.

Armin

On Wed, 7 Mar 2007, Giedrius Augys wrote:
> Hello,
> I have problem with capi, I can't install it. I have putted all info what I
> did and what I get :). I think you can suggest me how to solve this
> problem.and thanking you in anticipation. I have ISDN Frtiz!Card PCI
> v2.1and I want  to install it to my ubuntu box (kernel:
> 2.6.17-10-server). Using command "lspci -vv" , I can see that kernel finds
> this card:
> *02:0d.0 Network controller: AVM Audiovisuelles MKTG & Computer System GmbH
> Fritz!PCI v2.0 ISDN (rev 02)
>        Subsystem: AVM Audiovisuelles MKTG & Computer System GmbH Fritz!PCI
> v2.0 ISDN
>        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
>        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 201
> Region 0: Memory at ff9fec00 (32-bit, non-prefetchable) [size=32]
> Region 1: I/O ports at df80 [size=32]
> Capabilities: [40] Power Management version 2
>                Flags: PMEClk- DSI- D1- D2+ AuxCurrent=55mA
> PME(D0-,D1-,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-*
> 
> 
> 
>  I found tutorial in http://www.asteriskguru.com/tutorials/avm_b1.html .I
> have installed these packages:
> *ii  capiutils                      3.9.20060704-1          Utilities for
> CAPI-capable ISDN cards
> ii  libcapi20-3                    3.9.20060704-1          libraries for
> CAPI support
> ii  libcapi20-dev                  3.9.20060704-1          libraries for
> CAPI support
> ii  avm-fritz-firmware-2.6.17-10   3.11+2.6.17.7-10.1      Firmware for AVM
> Fritz! ISDN hardware*
> 
> and downloaded firmaware from *
> ftp://ftp.in-berlin.de/pub/capi4linux/firmware/b1/ .*My capi.conf is:
> *b1pci           /usr/share/isdn/b1.t4           DSS1    -       -
> -       -       P2P*
> 
> Then I exec command capiinit start, I have noting on output, but it load
> modules:
> *root at asterisk:~# lsmod
> Module                  Size  Used by
> b1pci                  10624  0
> b1dma                  17412  1 b1pci
> b1                     25856  2 b1pci,b1dma
> capi                   19392  0
> kernelcapi             49664  4 b1pci,b1dma,b1,capi
> capifs                  7176  2 capi
> ipv6                  271136  12
> lp                     12964  0
> mISDN_l2               44288  0
> mISDN_l1               13192  0
> avmfritz               25740  0
> mISDN_isac             17280  1 avmfritz
> mISDN_core             75648  4 mISDN_l2,mISDN_l1,avmfritz,mISDN_isac*
> 
> But when I execute command cappinfo, I get :
> *root at asterisk:~# capiinfo
> capi not installed - No such device or address (6).
> *
>