[asterisk-users] Re: asterisk-users Digest, Vol 30, Issue 79

[Robert Jenkins]

Hi,
 
what do you now get in the way of error messages?
 
 
Robert Jenkins.
 


  _____  

From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Vidura
Senadeera
Sent: 19 January 2007 23:03
To: asterisk-users at lists.digium.com
Cc: support at digium.com
Subject: [asterisk-users] Re: asterisk-users Digest, Vol 30, Issue 79




Hi,

 
 I checked by changing to from-zaptel, but no luck yet. Pls guide me on
this.
 
Regards,
vudura senadeera

 


------------------------------

Message: 9
Date: Fri, 19 Jan 2007 16:47:18 -0000
From: "Robert Jenkins" < raj at jrw.co.uk>
Subject: RE: [asterisk-users] Integrating asterisk with Toshiba
       Astrata DK380
To: "'Asterisk Users Mailing List - Non-Commercial Discussion'" 
       <asterisk-users at lists.digium.com>
Message-ID: <005701c73be9$7c907850$2800a8c0 at office >
Content-Type: text/plain; charset="us-ascii" 

Hi,

your zapata.con has 'context=from-pstn'

Try changing this to 'context=from-zaptel'

Robert Jenkins.



_____

From: asterisk-users-bounces at lists.digium.com
[mailto:  <mailto:asterisk-users-bounces at lists.digium.com>
asterisk-users-bounces at lists.digium.com] On Behalf Of Vidura
Senadeera
Sent: 19 January 2007 15:19
To: asterisk-users at lists.digium.com
Cc: support at digium.com
Subject: [asterisk-users] Integrating asterisk with Toshiba Astrata DK380 



Deat all,

I am in middle of integrate Asterisk with Toshiba astrata legacy pbx.

Following is my setup

Asterisk <-> Digium TE110P <-> E1 card in toshiba pbx <-> Toshiba PBX 

A =============================================> B
C <============================================ D

Asterisk PBX and strata PBX connected using back to back E1 cross cable.
Physicall connectivity is OK. The digium TE110p 
LED state green. zttool also OK.

Toshiba stata configured to make outbound call via E1 link with pressing 9
and then the out side number.

I was able to make call from soft phone to analog extension at toshiba pbx. 
A==> B way as shown above. But when trying to dial from
Toshiba PBX analog extension to asterisk extension, by pressing 9 the call
rejected.

In the asterisk command prompt I'm having following error message. 

-- Extension '' in context 'from-pstn' from '' does not exist.  Rejecting
call on channel 0/31, span 1

Is there any wrong in my setup. dial plan??, additional configuration if i
required to put please guide me.

I will be greately appreciated your feedback on this regard.

configuration details

/etc/zaptel.conf
# Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" 

span=1,1,0,ccs,hdb3,crc4
bchan=1-15,17-31
dchan=16

/etc/asterisk/zapata.conf

signalling=pri_net ; pri_cpe = PRI slave ; pri_net = PRI master
switchtype=euroisdn
;switchtype=national
echocancel=yes ; You can set this to 32, 64, or 128, tweak to your needs. 
echocancelwhenbridged=yes
echotraining=400 ; Asterisk trains to the beginning of the call, number is
in milliseconds
callerid=asreceived
overlapdial=no
pridialplan=unknown
immediate=no
;rxwink=300 
callprogress=no
loadzone=au
context=from-pstn ; Points to the default context of your extensions.conf
group=2
channel=>1-15
channel=>17-31 ;PRI/E1 link


[trunkgroups]
trunkgroup=>2,16 
spanmap=1,2,1



/etc/asterisk/extension.conf

[from-zaptel]
exten => _X.,1,Set(DID=${EXTEN})
exten => _X.,n,Goto(s,1)
exten => s,1,NoOp(Entering from-zaptel with DID == ${DID})
; If ($did == "") { $did = "s"; }
exten => s,n,Set(DID=${IF($["${DID}"= ""]?s:${DID})})
exten => s,n,NoOp(DID is now ${DID})
exten => s,n,GotoIf($["${CHANNEL:0:3}"="Zap"]?zapok:notzap) 
exten => s,n(notzap),Goto(ext-did,${DID},1)
; If there's no ext-did,s,1, that means there's not a no did/no cid route.
Hangup.
exten => s,n,Macro(hangup)
exten => s,n(zapok),NoOp(Is a Zaptel Channel) 
exten => s,n,Set(CHAN=${CHANNEL:4})
exten => s,n,Set(CHAN=${CUT(CHAN,-,1)})
exten => s,n,Macro(from-zaptel-${CHAN},${DID},1)
; If nothing there, then treat it as a DID
exten => s,n,NoOp(Returned from Macro from-zaptel-${CHAN}) 
exten => s,n,Goto(ext-did,${DID},1)




--
Thanks & Regards,
Vidura B. Senadeera.

-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20070119/0dd5e0
be/attachment-0001.htm

------------------------------

Message: 10
Date: Fri, 19 Jan 2007 11:46:57 -0500
From: "Chris Earle \(CBL\)" < cearle at cbltech.ca>
Subject: [asterisk-users] Disconnect Supervision UK / BT solution?
To: <  <mailto:asterisk-users at lists.digium.com>
asterisk-users at lists.digium.com >
Message-ID: <013b01c73be9$6ec87c40$6b01a8c0 at Chrisdev>
Content-Type: text/plain;       charset="iso-8859-1"

Hi all

I'm using sangoma a200 cards in the UK and have the ongoing, often noted 
problem of disconnect supervision with BT POTS lines.

Just noticed this post on
http://www.voip-info.org/wiki/view/UK+Asterisk+Details
stating that potentially someone's got a solution :

"TDM400P &amp; Not Detecting Hangups:

Got a TDM400P installed and having problems with Asterisk not detecting 
hangups? Using BT? If so, contact BT and ask what the "Disconnect Clear 
Time" setting is for your phone line. Odds are it's probably 100. Increasing
it to 800 fixed the issue for me.

"Disconnect Clear Time" is BT's name for CPC. " 


Does anyone have any thoughts/confirmation about this finally being a viable

solution?  This disconnect supervision problem has plagued TDM and Sangoma
cards for a long time!

Comments appreciated before I get on the phone with BT 


--
Chris Earle
System Solutions Specialist 



-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070120/b20bbd36/attachment.htm