[asterisk-users] Re: asterisk-users Digest, Vol 30, Issue 79

Fri Jan 19 16:03:14 MST 2007

>
>
>  Hi,
>
>
>  I checked by changing to from-zaptel, but no luck yet. Pls guide me on
> this.
>
> Regards,
> vudura senadeera
>
>
> ------------------------------
> >
> > Message: 9
> > Date: Fri, 19 Jan 2007 16:47:18 -0000
> > From: "Robert Jenkins" < raj at jrw.co.uk>
> > Subject: RE: [asterisk-users] Integrating asterisk with Toshiba
> >        Astrata DK380
> > To: "'Asterisk Users Mailing List - Non-Commercial Discussion'"
> >        <asterisk-users at lists.digium.com>
> > Message-ID: <005701c73be9$7c907850$2800a8c0 at office>
> > Content-Type: text/plain; charset="us-ascii"
> >
> > Hi,
> >
> > your zapata.con has 'context=from-pstn'
> >
> > Try changing this to 'context=from-zaptel'
> >
> > Robert Jenkins.
> >
> >
> >
> > _____
> >
> > From: asterisk-users-bounces at lists.digium.com
> > [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Vidura
> > Senadeera
> > Sent: 19 January 2007 15:19
> > To: asterisk-users at lists.digium.com
> > Cc: support at digium.com
> > Subject: [asterisk-users] Integrating asterisk with Toshiba Astrata
> > DK380
> >
> >
> >
> > Deat all,
> >
> > I am in middle of integrate Asterisk with Toshiba astrata legacy pbx.
> >
> > Following is my setup
> >
> > Asterisk <-> Digium TE110P <-> E1 card in toshiba pbx <-> Toshiba PBX
> >
> > A =============================================> B
> > C <============================================ D
> >
> > Asterisk PBX and strata PBX connected using back to back E1 cross cable.
> > Physicall connectivity is OK. The digium TE110p
> > LED state green. zttool also OK.
> >
> > Toshiba stata configured to make outbound call via E1 link with pressing
> > 9
> > and then the out side number.
> >
> > I was able to make call from soft phone to analog extension at toshiba
> > pbx.
> > A==> B way as shown above. But when trying to dial from
> > Toshiba PBX analog extension to asterisk extension, by pressing 9 the
> > call
> > rejected.
> >
> > In the asterisk command prompt I'm having following error message.
> >
> > -- Extension '' in context 'from-pstn' from '' does not
> > exist.  Rejecting
> > call on channel 0/31, span 1
> >
> > Is there any wrong in my setup. dial plan??, additional configuration if
> > i
> > required to put please guide me.
> >
> > I will be greately appreciated your feedback on this regard.
> >
> > configuration details
> >
> > /etc/zaptel.conf
> > # Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0"
> >
> > span=1,1,0,ccs,hdb3,crc4
> > bchan=1-15,17-31
> > dchan=16
> >
> > /etc/asterisk/zapata.conf
> >
> > signalling=pri_net ; pri_cpe = PRI slave ; pri_net = PRI master
> > switchtype=euroisdn
> > ;switchtype=national
> > echocancel=yes ; You can set this to 32, 64, or 128, tweak to your
> > needs.
> > echocancelwhenbridged=yes
> > echotraining=400 ; Asterisk trains to the beginning of the call, number
> > is
> > in milliseconds
> > callerid=asreceived
> > overlapdial=no
> > pridialplan=unknown
> > immediate=no
> > ;rxwink=300
> > callprogress=no
> > loadzone=au
> > context=from-pstn ; Points to the default context of your
> > extensions.conf
> > group=2
> > channel=>1-15
> > channel=>17-31 ;PRI/E1 link
> >
> >
> > [trunkgroups]
> > trunkgroup=>2,16
> > spanmap=1,2,1
> >
> >
> >
> > /etc/asterisk/extension.conf
> >
> > [from-zaptel]
> > exten => _X.,1,Set(DID=${EXTEN})
> > exten => _X.,n,Goto(s,1)
> > exten => s,1,NoOp(Entering from-zaptel with DID == ${DID})
> > ; If ($did == "") { $did = "s"; }
> > exten => s,n,Set(DID=${IF($["${DID}"= ""]?s:${DID})})
> > exten => s,n,NoOp(DID is now ${DID})
> > exten => s,n,GotoIf($["${CHANNEL:0:3}"="Zap"]?zapok:notzap)
> > exten => s,n(notzap),Goto(ext-did,${DID},1)
> > ; If there's no ext-did,s,1, that means there's not a no did/no cid
> > route.
> > Hangup.
> > exten => s,n,Macro(hangup)
> > exten => s,n(zapok),NoOp(Is a Zaptel Channel)
> > exten => s,n,Set(CHAN=${CHANNEL:4})
> > exten => s,n,Set(CHAN=${CUT(CHAN,-,1)})
> > exten => s,n,Macro(from-zaptel-${CHAN},${DID},1)
> > ; If nothing there, then treat it as a DID
> > exten => s,n,NoOp(Returned from Macro from-zaptel-${CHAN})
> > exten => s,n,Goto(ext-did,${DID},1)
> >
> >
> >
> >
> > --
> > Thanks & Regards,
> > Vidura B. Senadeera.
> >
> > -------------- next part --------------
> > An HTML attachment was scrubbed...
> > URL:
> > http://lists.digium.com/pipermail/asterisk-users/attachments/20070119/0dd5e0be/attachment-0001.htm
> >
> > ------------------------------
> >
> > Message: 10
> > Date: Fri, 19 Jan 2007 11:46:57 -0500
> > From: "Chris Earle \(CBL\)" < cearle at cbltech.ca>
> > Subject: [asterisk-users] Disconnect Supervision UK / BT solution?
> > To: <asterisk-users at lists.digium.com >
> > Message-ID: <013b01c73be9$6ec87c40$6b01a8c0 at Chrisdev>
> > Content-Type: text/plain;       charset="iso-8859-1"
> >
> > Hi all
> >
> > I'm using sangoma a200 cards in the UK and have the ongoing, often noted
> >
> > problem of disconnect supervision with BT POTS lines.
> >
> > Just noticed this post on
> > http://www.voip-info.org/wiki/view/UK+Asterisk+Details
> > stating that potentially someone's got a solution :
> >
> > "TDM400P &amp; Not Detecting Hangups:
> >
> > Got a TDM400P installed and having problems with Asterisk not detecting
> > hangups? Using BT? If so, contact BT and ask what the "Disconnect Clear
> > Time" setting is for your phone line. Odds are it's probably 100.
> > Increasing
> > it to 800 fixed the issue for me.
> >
> > "Disconnect Clear Time" is BT's name for CPC. "
> >
> >
> > Does anyone have any thoughts/confirmation about this finally being a
> > viable
> > solution?  This disconnect supervision problem has plagued TDM and
> > Sangoma
> > cards for a long time!
> >
> > Comments appreciated before I get on the phone with BT
> >
> >
> > --
> > Chris Earle
> > System Solutions Specialist
> >
> >
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070119/fc943d05/attachment-0001.htm