[asterisk-users] Cisco 7970 with skinny on * 1.4.x

[Richard Klingler]

A little with skinny debug set to on shows during register:

Device SEP00175A872053 is attempting to register
Requesting capabilities
Buttontemplate requested
Adding button: 9, 1
Sending 30006 template to cisco
Received SoftKey Template Request
Received SoftKeySetReq
RECEIVED UNKNOWN MESSAGE TYPE:  c
Received CapabilitiesRes
Adding codec capability '0 (25)'
Adding codec capability '4 (4)'
Adding codec capability '8 (2)'
Adding codec capability '0 (15)'
Adding codec capability '0 (16)'
Adding codec capability '0 (11)'
Adding codec capability '256 (12)'
Adding codec capability '256 (12)'
Adding codec capability '0 (257)'
Device capability set to '268'
RECEIVED UNKNOWN MESSAGE TYPE:  49
RECEIVED UNKNOWN MESSAGE TYPE:  49
RECEIVED UNKNOWN MESSAGE TYPE:  4a
RECEIVED UNKNOWN MESSAGE TYPE:  9
Received Time/Date Request
Received Alarm Message: 32: Name=SEP00175A872053 Load= SCCP70.8-2-2SR1S 
: Invalid SCCP message! : ID :92


It also show this message when going offhook:

RECEIVED UNKNOWN MESSAGE TYPE:  49
Setting ringer mode to '1'.
skinny_new: tmp->nativeformats=268 fmt=4
Attempting to Clear display on Skinny 995 at cisco
Clearing Display
Received Alarm Message: 32: Name=SEP00175A872053 Load= SCCP70.8-2-2SR1S 
: Invalid SCCP message! : ID :85
Received Alarm Message: 32: Name=SEP00175A872053 Load= SCCP70.8-2-2SR1S 
: Invalid SCCP message! : ID :11
Received Alarm Message: 32: Name=SEP00175A872053 Load= SCCP70.8-2-2SR1S 
: Invalid SCCP message! : ID :9a
Received Alarm Message: 32: Name=SEP00175A872053 Load= SCCP70.8-2-2SR1S 
: Invalid SCCP message! : ID :82


Looks to me that chan_skinny doesn't understand many important messages.
Any previous 7970G SCCP firmware that might work?

cheers
rick


Richard Klingler schrieb:
> Sorry bringing it up again....
> 
> Meanwhile switched to asterisk 1.4.3 on fbsd-6.2 but still
> no luck getting my 7970G to run via skinny...
> 
> It registers fine with *:
> 
> Adding button: 9, 1
> Device capability set to '268'
> asterisk*CLI> skinny show devices
> Name                 DeviceId         IP              Type            R NL
> -------------------- ---------------- --------------- --------------- - --
> cisco                SEP00175A872053  xx.xx.xxx.xx    7970            Y  1
> 
> 
> But on the phone I just see displayed the time and date but no
> linelabel...
> 
> My skinny.conf is:
> 
> [general]
> bindaddr=xx.xx.xxx.xx   ; Address to bind to
> bindport=2000           ; Port to bind to, default tcp/2000
> dateformat=D.M.Y        ; M,D,Y in any order (5 chars max)
> keepalive=30
> disallow=all
> allow=all               ; see doc/rtp-packetization for framing options
> 
> [cisco]
> device=SEP00175A872053
> model=7970
> nat=1
> callerid="Richard Klingler" <995>
> mailbox=995
> callwaiting=yes
> transfer=yes
> threewaycalling=yes
> context=klingler
> linelabel="phonelab"
> line => 995
> 
> 
> any ideas left?
> 
> Using now "cmterm-7970_7971-sccp.8-2-2SR1"
> 
> cheers
> rick
> 
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
> 
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
> 
> .
>