[asterisk-users] Sangoma A101 gives 'no PRI configured on span 1' error

[yusuf]

Zeeshan Zakaria wrote:
> I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, 
> and installation was successful. zttool, ztcfg, all show card is 
> installed properly. I copied the parameters from my old working 
> zaptel.conf, zapata.conf and zapata-auto.conf. Verified on Sangoma 
> website that these files are correct. Also configured wanpipe1.conf.
> 
> But doing all this didn't start the PRI channels. It says 'no PRI 
> configured on span 1' on Asterisk CLI on typing 'pri show span 1'.
> 
> What am I missing here?
> 
> -- 
> Zeeshan A Zakaria

Hi,

This is my .conf files  (edited for brevity)

zaptel.conf

span=1,1,0,ccs,hdb3,crc4

bchan=1-15,17-31
dchan=16

zapata.conf
switchtype=euroisdn

group=0
context=inbound
signalling=pri_net
;group=1
callerid=asreceived
channel => 1-15,17-31


wanpipe1.conf

[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment

[wanpipe1]
CARD_TYPE       = AFT
S514CPU         = A
CommPort        = PRI
AUTO_PCISLOT    = NO
PCISLOT         = 1
PCIBUS          = 3
FE_MEDIA        = E1
FE_LCODE        = HDB3
FE_FRAME        = NCRC4
FE_LINE         = 1
TE_CLOCK        = NORMAL
ACTIVE_CH       = ALL
TE_HIGHIMPEDANCE        = NO
INTERFACE       = V35
CLOCKING        = EXTERNAL
BaudRate        = 0
MTU             = 1500
UDPPORT         = 9000
TTL             = 255
IGNORE_FRONT_END = NO

[w1g1]
PROTOCOL        = HDLC
HDLC_STREAMING  = NO
ACTIVE_CH       = ALL
IDLE_FLAG       = 0x7E
MTU             = 1500
MRU             = 1500
TDMV_SPAN       = 1
TDMV_ECHO_OFF   = NO
MULTICAST       = NO
TRUE_ENCODING_TYPE      = NO

[root at ecnboksburg ~]# wanrouter status

Devices currently active:
         wanpipe1


Wanpipe Config:

Device name | Protocol Map | Adapter  | IRQ | Slot/IO | If's | CLK | Baud rate |
wanpipe1    | N/A          | A101/2   | 201 | 1       | 1    | EXT | 0         |

Wanrouter Status:

Device name | Protocol | Station | Status        |
wanpipe1    | AFT HDLC | N/A     | Connected     |


[root at ecnboksburg ~]# wanrouter hwprobe

-------------------------------
| Wanpipe Hardware Probe Info |
-------------------------------
1 . AFT-A101u  : SLOT=1 : BUS=3 : IRQ=201 : CPU=A : PORT=PRI

Card Cnt: S508=0  S514X=0  S518=0  A101-2=1  A104=0  A300=0


ecnboksburg*CLI> zap show status
Description                              Alarms     IRQ        bpviol     CRC4
wanpipe1 card 0                          OK         0          0          0




-- 
thanks,
yusuf

-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.