[asterisk-users] Diva server 4bri and Portuguese BRI

[Armin Schindler]

On Wed, 1 Nov 2006, Pedro Silva wrote:
> Hello,
> 
> The problem was wrong contexts defined like Marco said, and is solved.
> Now, i have another problem...of course :)
> 
> On incoming calls, i only can receive calls if i define a line like
> the following, in extensions.conf:
> exten => _.,n,Dial(SIP/500,30,tr) (all incoming calls are redirected
> to extension 500).
> The problem is that i have some DDI's assigned by my telco (xxx302500
> to xxx302509) and i need to route each DDI to diferent internal
> extension.
> If i define someting like "exten => _XXXXXXXX0,n,Dial..." (for DDI
> xxx302500) the call is not answered by asterisk. I think that asterisk
> cannot identify the destination DDI of the incoming call...is this
> normal?

As you can see in the log below, the called number is just '0':
> CalledPartyNumber               = <81>0

It seems DDI 0 of your line was called. So just do
  exten => 0,n,Dial...

Armin

> This is the capi debug of one incoming call:
> 
> asterisk1*CLI>
> CONNECT_IND ID=001 #0x1975 LEN=0045
> Controller/PLCI/NCCI            = 0x401
> CIPValue                        = 0x10
> CalledPartyNumber               = <81>0
> CallingPartyNumber              = <00 83>XXXXXXXXX
> CalledPartySubaddress           = default
> CallingPartySubaddress          = default
> BC                              = <80 90 a3>
> LLC                             = default
> HLC                             = <91 81>
> AdditionalInfo
> BChannelinformation            = default
> Keypadfacility                 = default
> Useruserdata                   = default
> Facilitydataarray              = default
> 
> -- CONNECT_IND (PLCI=0x401,DID=0,CID=XXXXXXXXX,CIP=0x10,CONTROLLER=0x1)
> > ISDN1#02: msn='*' DNID='0' MSN
> == ISDN1#02: setting format alaw - 0x8 (alaw)
> == ISDN1#02: Incoming call 'XXXXXXXXX' -> '0'
> INFO_IND ID=001 #0x1976 LEN=0017
> Controller/PLCI/NCCI            = 0x401
> InfoNumber                      = 0x70
> InfoElement                     = <81>0
> 
> INFO_RESP ID=001 #0x1976 LEN=0012
> Controller/PLCI/NCCI            = 0x401
> 
> -- ISDN1#02: info element CALLED PARTY NUMBER
> > ISDN1#02: INFO_IND DID digits not used in this state.
> INFO_IND ID=001 #0x1977 LEN=0015
> Controller/PLCI/NCCI            = 0x401
> InfoNumber                      = 0xa1
> InfoElement                     = default
> 
> INFO_RESP ID=001 #0x1977 LEN=0012
> Controller/PLCI/NCCI            = 0x401
> 
>    -- ISDN1#02: info element Sending Complete
> CONNECT_RESP ID=001 #0x1977 LEN=0032
> Controller/PLCI/NCCI            = 0x401
> Reject                          = 0x1
> BProtocol
> B1protocol                     = 0x0
> B2protocol                     = 0x0
> B3protocol                     = 0x0
> B1configuration                = default
> B2configuration                = default
> B3configuration                = default
> ConnectedNumber                 = default
> ConnectedSubaddress             = default
> LLC                             = default
> AdditionalInfo
> BChannelinformation            = default
> Keypadfacility                 = default
> Useruserdata                   = default
> Facilitydataarray              = default
> 
> INFO_IND ID=001 #0x1978 LEN=0016
> Controller/PLCI/NCCI            = 0x401
> InfoNumber                      = 0x18
> InfoElement                     = <81>
> 
> INFO_RESP ID=001 #0x1978 LEN=0012
> Controller/PLCI/NCCI            = 0x401
> 
>    -- ISDN1#02: info element CHANNEL IDENTIFICATION 81
> INFO_IND ID=001 #0x1979 LEN=0015
> Controller/PLCI/NCCI            = 0x401
> InfoNumber                      = 0x8005
> InfoElement                     = default
> 
> INFO_RESP ID=001 #0x1979 LEN=0012
> Controller/PLCI/NCCI            = 0x401
> 
> -- ISDN1#02: info element SETUP
> > ISDN1#02: IE SETUP / SENDING-COMPLETE already received.
> DISCONNECT_IND ID=001 #0x197b LEN=0014
> Controller/PLCI/NCCI            = 0x401
> Reason                          = 0x0
> 
> DISCONNECT_RESP ID=001 #0x197b LEN=0012
> Controller/PLCI/NCCI            = 0x401
> 
> -- ISDN1#02: DISCONNECT_IND on incoming without pbx, doing hangup.
> > CAPI/ISDN1/0-15: set channel task to 1
> == ISDN1#02: CAPI Hangingup for PLCI=0x401 in state 4
> == ISDN1#02: Interface cleanup PLCI=0x401
> > CAPI devicestate requested for ISDN1/0
> 
> Anyone can give me ideas about this problem?
> Thanks in advance!
> Best regards,
> PS.
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
> 
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
>