[Asterisk-Users] TDM400P zttest not working

Antonio Moragues amoragues at gmail.com
Thu Jan 19 15:53:37 MST 2006


Hi,

    I have a TDM400P running with only one FXO port running on a VIA
EPIA MS10000 (1Ghz Via Eden). When I run zttest from Zaptel 1.2.1 it
hang and when I interrupt it with Ctrl-C that is the result: ¿anyone
have some idea about why isn't working?

Some additional info:

# /usr/src/zaptel/zttest -v
Opened pseudo zap interface, measuring accuracy...

--- Results after 0 passes ---
Best: 0.000000 -- Worst: 100.000000 -- Average: 100.000000

Some info:

# lsmod
Module                  Size  Used by
wctdm                  35264  1
zaptel                188804  7 wctdm
binfmt_misc            12040  1

# cat /proc/interrupts
           CPU0
  0:     705996          XT-PIC  timer
  1:          8          XT-PIC  i8042
  2:          0          XT-PIC  cascade
  5:          0          XT-PIC  uhci_hcd:usb4, uhci_hcd:usb5
  8:          1          XT-PIC  rtc
  9:          0          XT-PIC  acpi
  10:        100          XT-PIC  ehci_hcd:usb1
  11:       2834          XT-PIC  uhci_hcd:usb2, uhci_hcd:usb3, eth0, wctdm
  12:        114          XT-PIC  i8042
  14:       6880          XT-PIC  ide0
NMI:          0
LOC:          0
ERR:          0
MIS:          0

# info from dmesg

Zapata Telephony Interface Registered on major 196
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
Freshmaker version: 73
Freshmaker passed register test
Module 0: Not installed
Module 1: Not installed
Module 2: Not installed
Module 3: Installed -- AUTO FXO (FCC mode)
Found a Wildcard TDM: Wildcard TDM400P REV I (1 modules)
Registered tone zone 0 (United States / North America)
Registered tone zone 0 (United States / North America)

# lspci -vvv

00:13.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
Modem/ISDN interface
        Subsystem: Unknown device b119:0003
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (250ns min, 32000ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at ec00 [size=256]
        Region 1: Memory at e6402000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA
PME(D0+,D1-,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-


Best Regards.

Antonio.



More information about the asterisk-users mailing list