[Asterisk-Users] loading zaptel drivers automatically upon reboot

[Carlos Alperin]

[root at SIP2-MI zaptel]# chkconfig --list zaptel
zaptel          0:off   1:off   2:on    3:on    4:on    5:on    6:off

[root at SIP2-MI zaptel]# chkconfig --list asterisk
asterisk        0:off   1:off   2:on    3:off   4:on    5:on    6:off

Are not this numbers the runlevels defined on INITTAB?

# Default runlevel. The runlevels used by RHS are:
#  0 - halt (Do NOT set initdefault to this)
#  1 - Single user mode
#  2 - Multiuser, without NFS (The same as 3, if you do not have networking)
#  3 - Full multiuser mode
#  4 - unused
#  5 - X11
#  6 - reboot (Do NOT set initdefault to this)
#

If not, then I should put zaptel on on 1, and asterisk on on 3? Is this
correct?

Thanks,

Carlos

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Tzafrir Cohen
Sent: Monday, January 16, 2006 3:03 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [Asterisk-Users] loading zaptel drivers automatically upon
reboot

On Sat, Jan 14, 2006 at 03:55:50PM -0500, Carlos Alperin wrote:
> After install everything on the supposedly right place, my conclusion is
> that zaptel doesn't load wct1xxp module. 

That's easy to test: before you restart zaptel, look at /proc/zaptel .
if /proc/zaptel exists, zaptel was loaded . if /proc/zaptel/1 exists and
reports those 24 channels, then wct1xxp has loaded and identified your
card.

Another possible reason: make sure that the zaptel init.d script runs
before the asterisk one. It needs to have a lower "start" number. Use
'chkconfig --list asterisk' and 'chkconfig --list zaptel' to verify
that.

> 
> Then, that is the reason for Asterisk to fail loading.
> 
> However I change the MODULES & RMODULES on the zaptel on /etc/init.d &
> /etc/sysconfig, it continuous same way.
> 
> Carlos Alperin
> 
> -----Original Message-----
> From: asterisk-users-bounces at lists.digium.com
> [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Tzafrir
Cohen
> Sent: Saturday, January 14, 2006 2:36 PM
> To: asterisk-users at lists.digium.com
> Subject: Re: [Asterisk-Users] loading zaptel drivers automatically upon
> reboot
> 
> On Fri, Jan 13, 2006 at 09:39:09PM -0500, Carlos Alperin wrote:
> > That is right for zaptel. But you still has to do modprobe wctdm on
> rc.local
> > before to load asterisk.
> 
> rc.local is run after the standard init.d scripts. Thus if you load
> asterisk in an init.d script, you'd be loading the zaptel modules too
> late.
> 
> Just add another init.d script. See the skeleton in /etc/init.d (there's
> a README there IIRC).
> 
> -- 
> Tzafrir Cohen         | tzafrir at jbr.cohens.org.il | VIM is
> http://tzafrir.org.il |                           | a Mutt's  
> tzafrir at cohens.org.il |                           |  best
> ICQ# 16849755         |                           | friend
> 
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
> 
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
> 
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
> 
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users

-- 
Tzafrir Cohen         | tzafrir at jbr.cohens.org.il | VIM is
http://tzafrir.org.il |                           | a Mutt's  
tzafrir at cohens.org.il |                           |  best
ICQ# 16849755         |                           | friend

_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users