[Asterisk-Users] Having major issues with TDM2400

[gw at adcomcorp.com]

Oh just a followup, if you are trying to do an outbound dialout over
analog, what others are saying is correct.  You could consider however
using a voip provider to make the outbound call, then you should have
status.

Greg
 

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Gregory
Wiktor - ADCom Corp.
Sent: Sunday, January 01, 2006 8:05 PM
To: asterisk-users at lists.digium.com
Subject: RE: [Asterisk-Users] Having major issues with TDM2400

Hello Kerry, I do it exactly as such, however in steps.  My
understanding of the hint system is just for notification of status, not
for execution of dialing. 

I regularly use this same setup you are looking for, rings in, then
rings 2-5 devices (some zap, some iax) and the first one that answers
gets the call.

Make sure you use the Dial( command I replied with previously. (avoid
hint for testing).

Looking at your emails, it looks like you need to review the dialplan
setup, for example the hint and && do not look right to me.

One example for me: exten =>
s,8,Dial(IAX2/ArdsleySomers/314&IAX2/ArdsleySomers/331,,)

But it is the same as SIP/220&Zap/5, etc.

I cannot say anything specific to amp however.

Greg

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Kerry
Garrison
Sent: Sunday, January 01, 2006 7:34 PM
To: 'Asterisk Users Mailing List - Non-Commercial Discussion'
Subject: RE: [Asterisk-Users] Having major issues with TDM2400

The goal is to create a user that has a SIP device and a custom ZAP
channel device, have them both ring until one is answered, basically a
ring group.
But I am using AMP's users and device mode rather than the extensions
mode.
I have this working properly on my office system. However, with the
TDM2400 I cannot have both the zap channel and sip channel ringing at
the same time and only handing the call to the end device that answers
the call. I don't understand why this is so difficult for everyone to
grasp. Send a call to both a custom ZAP device and a sip phone and
whoever answers it gets the call.
-Kerry


 

> -----Original Message-----
> From: asterisk-users-bounces at lists.digium.com
> [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of C F
> Sent: Sunday, January 01, 2006 4:14 PM
> To: Asterisk Users Mailing List - Non-Commercial Discussion
> Subject: Re: [Asterisk-Users] Having major issues with TDM2400
> 
> On 12/31/05, Kerry Garrison <support at techdatapros.com> wrote:
> > To summarize, I spent 6 hours yesterday on the phone with Digium 
> > trying to fix a problem with the TDM2400 ad we still don't have it 
> > working right. The lastest version of everything are installed and 
> > confirmed by Digium. So here is the issue:
> >
> > Zapata.conf
> > ; Disable call progress
> > ; callprogress=yes
> >
> > Outbound calls to PSTN phone numbers work properly
> >
> > But using this:
> >
> > exten => 100,hint,SIP/900&&zap/g0/w5551212
> 
> What are you trying to do here? You trying to hint to a zip channel 
> and dial a number using the hint priority?
> 
> >
> > The extension will ring once, but as soon as the PSTN line
> is picked
> > up, the sip phone stops ringing because * thinks the phone
> has been answered.
> 
> Which makes sense to me, since as soon as you start dialing you *are* 
> off hook, which in analog means the phone *is* answered. Since all the

> singalling is done in band, it is not difference than picking up the 
> Zap channel for incoming call, at which point you also understand it's

> considered answered.
> 
> >
> > Zapata.conf
> > ; Enable call progress
> > callprogress=yes
> >
> > Outbound calls to PSTN phone numbers will dial out but there is no 
> > answer detection from the far side. The far side may answer
> the phone
> > but * keeps ringing until the timeout expires.
> >
> 
> So don't use callprogress if it doesn't work for you, in no way do I 
> see this related to the subject line of this post.
> 
> > And using this:
> >
> > exten => 100,hint,SIP/900&&zap/g0/w5551212
> >
> 
> Again what is this suppose to do?
> 
> > Both the sip phone and zap line both ring at the same time
> until the time.
> > Picking up the sip phone bridges the call and disconnects
> the zap line
> > as it should.
> >
> > Any ideas? We are stuck until after the holidays at this point.
> > -Kerry
> >
> >
> >
> > _______________________________________________
> > --Bandwidth and Colocation provided by Easynews.com --
> >
> > Asterisk-Users mailing list
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-users
> >
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
> 
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
> 


_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users