[Asterisk-Users] Tormenta CAS signaling

Wed Feb 22 09:26:35 MST 2006

Viktor Tatianin wrote:

>Hi Steve
>
>
>May I change TX ABCD bits 0101 to 1001 or no ?
>  
>
Not when you use fxols. You can only control them when you use cas as 
the signalling type.

Steve

>-----Original Message-----
>From: asterisk-users-bounces at lists.digium.com
>[mailto:asterisk-users-bounces at lists.digium.com]On Behalf Of Steve Underwood
>Sent: Wednesday, February 22, 2006 3:28 PM
>To: Asterisk Users Mailing List - Non-Commercial Discussion
>Subject: Re: [Asterisk-Users] Tormenta CAS signaling
>
>
>Hi Viktor,
>
>So? You seem to have 5 channels set to fxols mode OK. What exactly that
>does, I am not sure. FXO operation is highly telco dependent with E1s. I
>believe what is implemented in zaptel is an arrangement to work with
>some E1 channel banks.
>
>Do you have an actual question this time?
>
>Steve
>
>
>Viktor Tatianin wrote:
>
>  
>
>>Hi Steve
>>I have next config
>>zttool
>>
>>Current Alarms:     No alarms.
>>Sync Source:        Tormenta 2 (PCI) Quad E1 Card
>>IRQ Misses:               0
>>Bipolar Viol:            14
>>Tx/Rx Levels:         0/  0
>>
>>Total/Conf/Act:      31/  6/  6
>>   1111111111222222222333
>>1234567890123456789012345789012
>>
>> TxA 000000
>> TxB 111111
>> TxC 000000
>> TxD 111111
>>
>>  RxA 111111
>>  RxB 011111
>>  RxC 011111
>>  RxD 111111
>>
>>
>>
>>
>>
>>
>>
>>ztcfg -vv
>>
>>Zaptel Configuration
>>======================
>>
>>SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
>>SPAN 2: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
>>
>>Channel map:
>>
>>Channel 01: Clear channel (Default) (Slaves: 01)
>>Channel 02: Clear channel (Default) (Slaves: 02)
>>Channel 03: Clear channel (Default) (Slaves: 03)
>>Channel 04: Clear channel (Default) (Slaves: 04)
>>Channel 05: Clear channel (Default) (Slaves: 05)
>>Channel 06: Clear channel (Default) (Slaves: 06)
>>Channel 07: Clear channel (Default) (Slaves: 07)
>>Channel 08: Clear channel (Default) (Slaves: 08)
>>Channel 09: Clear channel (Default) (Slaves: 09)
>>Channel 10: Clear channel (Default) (Slaves: 10)
>>Channel 11: Clear channel (Default) (Slaves: 11)
>>Channel 12: Clear channel (Default) (Slaves: 12)
>>Channel 13: Clear channel (Default) (Slaves: 13)
>>Channel 14: Clear channel (Default) (Slaves: 14)
>>Channel 15: Clear channel (Default) (Slaves: 15)
>>Channel 16: D-channel (Default) (Slaves: 16)
>>Channel 17: Clear channel (Default) (Slaves: 17)
>>Channel 18: Clear channel (Default) (Slaves: 18)
>>Channel 19: Clear channel (Default) (Slaves: 19)
>>Channel 20: Clear channel (Default) (Slaves: 20)
>>Channel 21: Clear channel (Default) (Slaves: 21)
>>Channel 22: Clear channel (Default) (Slaves: 22)
>>Channel 23: Clear channel (Default) (Slaves: 23)
>>Channel 24: Clear channel (Default) (Slaves: 24)
>>Channel 25: Clear channel (Default) (Slaves: 25)
>>Channel 26: Clear channel (Default) (Slaves: 26)
>>Channel 27: Clear channel (Default) (Slaves: 27)
>>Channel 28: Clear channel (Default) (Slaves: 28)
>>Channel 29: Clear channel (Default) (Slaves: 29)
>>Channel 30: Clear channel (Default) (Slaves: 30)
>>Channel 31: Clear channel (Default) (Slaves: 31)
>>Channel 32: FXO Loopstart (Default) (Slaves: 32)
>>Channel 33: FXO Loopstart (Default) (Slaves: 33)
>>Channel 34: FXO Loopstart (Default) (Slaves: 34)
>>Channel 35: FXO Loopstart (Default) (Slaves: 35)
>>Channel 36: FXO Loopstart (Default) (Slaves: 36)
>>Channel 37: FXO Loopstart (Default) (Slaves: 37)
>>
>>37 channels configured.
>>
>>this is zaptel.conf
>>
>>; Zapata telephony interface
>>;
>>; Configuration file
>>
>>[trunkgroups]
>>
>>[channels]
>>
>>language=en
>>context=from-isdn-external
>>;signalling=fxs_ks
>>;rxwink=300             ; Atlas seems to use long (250ms) winks
>>signalling=pri_cpe
>>switchtype=euroisdn
>>pridialplan=unknown
>>prilocaldialplan=unknown
>>callerid=asreceived
>>usedistinctiveringdetection=yes
>>usecallingpres=yes
>>
>>; Whether or not to do distinctive ring detection on FXO lines
>>;
>>;usedistinctiveringdetection=yes
>>
>>usecallerid=yes
>>hidecallerid=no
>>callwaiting=yes
>>usecallingpres=yes
>>callwaitingcallerid=yes
>>threewaycalling=yes
>>transfer=yes
>>cancallforward=yes
>>callreturn=yes
>>echocancel=yes
>>echocancelwhenbridged=yes
>>echotraining=400
>>rxgain=0.0
>>txgain=0.0
>>group=0
>>callgroup=1
>>pickupgroup=1
>>immediate=no
>>
>>;faxdetect=both
>>faxdetect=incoming
>>;faxdetect=outgoing
>>;faxdetect=no
>>
>>;Include genzaptelconf configs
>>#include zapata-auto.conf
>>
>>;Include AMP configs
>>#include zapata_additional.conf
>>channel=> 1-15,17-31
>>
>>signalling=fxo_ks
>>context=bank
>>group=1
>>cas=32-37:1101
>>channel=> 32-37
>>This is my zapata.conf
>>
>># Global data
>>
>>span=1,1,0,ccs,hdb3
>>bchan=1-15,17-31
>>dchan=16
>>
>>loadzone        = us
>>defaultzone     = us
>>
>>span=2,1,0,cas,hdb3
>>fxols=32-37
>>
>>
>>
>>
>>-----Original Message-----
>>From: asterisk-users-bounces at lists.digium.com
>>[mailto:asterisk-users-bounces at lists.digium.com]On Behalf Of Steve
>>    
>>
>Underwood
>  
>
>>Sent: Tuesday, February 21, 2006 2:59 PM
>>To: Asterisk Users Mailing List - Non-Commercial Discussion
>>Subject: Re: [Asterisk-Users] Tormenta CAS signaling
>>
>>
>>Viktor Tatianin wrote:
>>
>>
>>
>>    
>>
>>>Hi Steve
>>>
>>>I attempt change in  zapata.conf
>>>
>>>cas=1-15:1101   but use zttool view ABCD bits 1010
>>>
>>>Regards,
>>>Viktor
>>>
>>>
>>>
>>>
>>>      
>>>
>>Have you put the E1 in CAS mode with something like:
>>
>>span=1,1,0,cas,hdb3
>>
>>Steve
>>
>>
>>
>>    
>>
>>>-----Original Message-----
>>>From: asterisk-users-bounces at lists.digium.com
>>>[mailto:asterisk-users-bounces at lists.digium.com]On Behalf Of Steve
>>>
>>>
>>>      
>>>
>>Underwood
>>
>>
>>    
>>
>>>Sent: Friday, February 10, 2006 3:25 PM
>>>To: Asterisk Users Mailing List - Non-Commercial Discussion
>>>Subject: Re: [Asterisk-Users] Tormenta CAS signaling
>>>
>>>
>>>Viktor Tatianin wrote:
>>>
>>>
>>>
>>>
>>>
>>>      
>>>
>>>>Hello
>>>>
>>>>Can anyone know how may change(inverting) cas signaling ABCD bits at the
>>>>Tormenta 2 (four E1 ports) cards
>>>>My cards send idle code ABCD 0101 but my mux which use as channel bank
>>>>
>>>>
>>>>        
>>>>
>>wait
>>
>>
>>    
>>
>>>>ABCD 1001
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>        
>>>>
>>>The idle code is set in zapata.conf. For example:
>>>
>>>cas=1-15:1101
>>>
>>>Sets CAS mode for channels 1 to 15, with the idle pattern 1101.
>>>
>>>Regards,
>>>Steve
>>>
>>>
>>>
>>>
>>>      
>>>