[Asterisk-Users] Tormenta CAS signaling

Wed Feb 22 07:54:40 MST 2006

Hi Steve

May I change TX ABCD bits 0101 to 1001 or no ?

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com]On Behalf Of Steve Underwood
Sent: Wednesday, February 22, 2006 3:28 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [Asterisk-Users] Tormenta CAS signaling

Hi Viktor,

So? You seem to have 5 channels set to fxols mode OK. What exactly that
does, I am not sure. FXO operation is highly telco dependent with E1s. I
believe what is implemented in zaptel is an arrangement to work with
some E1 channel banks.

Do you have an actual question this time?

Steve

Viktor Tatianin wrote:

>Hi Steve
>I have next config
>zttool
>
>Current Alarms:     No alarms.
>Sync Source:        Tormenta 2 (PCI) Quad E1 Card
>IRQ Misses:               0
>Bipolar Viol:            14
>Tx/Rx Levels:         0/  0
>
>Total/Conf/Act:      31/  6/  6
>    1111111111222222222333
> 1234567890123456789012345789012
>
>  TxA 000000
>  TxB 111111
>  TxC 000000
>  TxD 111111
>
>   RxA 111111
>   RxB 011111
>   RxC 011111
>   RxD 111111
>
>
>
>
>
>
>
>ztcfg -vv
>
>Zaptel Configuration
>======================
>
>SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
>SPAN 2: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
>
>Channel map:
>
>Channel 01: Clear channel (Default) (Slaves: 01)
>Channel 02: Clear channel (Default) (Slaves: 02)
>Channel 03: Clear channel (Default) (Slaves: 03)
>Channel 04: Clear channel (Default) (Slaves: 04)
>Channel 05: Clear channel (Default) (Slaves: 05)
>Channel 06: Clear channel (Default) (Slaves: 06)
>Channel 07: Clear channel (Default) (Slaves: 07)
>Channel 08: Clear channel (Default) (Slaves: 08)
>Channel 09: Clear channel (Default) (Slaves: 09)
>Channel 10: Clear channel (Default) (Slaves: 10)
>Channel 11: Clear channel (Default) (Slaves: 11)
>Channel 12: Clear channel (Default) (Slaves: 12)
>Channel 13: Clear channel (Default) (Slaves: 13)
>Channel 14: Clear channel (Default) (Slaves: 14)
>Channel 15: Clear channel (Default) (Slaves: 15)
>Channel 16: D-channel (Default) (Slaves: 16)
>Channel 17: Clear channel (Default) (Slaves: 17)
>Channel 18: Clear channel (Default) (Slaves: 18)
>Channel 19: Clear channel (Default) (Slaves: 19)
>Channel 20: Clear channel (Default) (Slaves: 20)
>Channel 21: Clear channel (Default) (Slaves: 21)
>Channel 22: Clear channel (Default) (Slaves: 22)
>Channel 23: Clear channel (Default) (Slaves: 23)
>Channel 24: Clear channel (Default) (Slaves: 24)
>Channel 25: Clear channel (Default) (Slaves: 25)
>Channel 26: Clear channel (Default) (Slaves: 26)
>Channel 27: Clear channel (Default) (Slaves: 27)
>Channel 28: Clear channel (Default) (Slaves: 28)
>Channel 29: Clear channel (Default) (Slaves: 29)
>Channel 30: Clear channel (Default) (Slaves: 30)
>Channel 31: Clear channel (Default) (Slaves: 31)
>Channel 32: FXO Loopstart (Default) (Slaves: 32)
>Channel 33: FXO Loopstart (Default) (Slaves: 33)
>Channel 34: FXO Loopstart (Default) (Slaves: 34)
>Channel 35: FXO Loopstart (Default) (Slaves: 35)
>Channel 36: FXO Loopstart (Default) (Slaves: 36)
>Channel 37: FXO Loopstart (Default) (Slaves: 37)
>
>37 channels configured.
>
>this is zaptel.conf
>
>; Zapata telephony interface
>;
>; Configuration file
>
>[trunkgroups]
>
>[channels]
>
>language=en
>context=from-isdn-external
>;signalling=fxs_ks
>;rxwink=300             ; Atlas seems to use long (250ms) winks
>signalling=pri_cpe
>switchtype=euroisdn
>pridialplan=unknown
>prilocaldialplan=unknown
>callerid=asreceived
>usedistinctiveringdetection=yes
>usecallingpres=yes
>
>; Whether or not to do distinctive ring detection on FXO lines
>;
>;usedistinctiveringdetection=yes
>
>usecallerid=yes
>hidecallerid=no
>callwaiting=yes
>usecallingpres=yes
>callwaitingcallerid=yes
>threewaycalling=yes
>transfer=yes
>cancallforward=yes
>callreturn=yes
>echocancel=yes
>echocancelwhenbridged=yes
>echotraining=400
>rxgain=0.0
>txgain=0.0
>group=0
>callgroup=1
>pickupgroup=1
>immediate=no
>
>;faxdetect=both
>faxdetect=incoming
>;faxdetect=outgoing
>;faxdetect=no
>
>;Include genzaptelconf configs
>#include zapata-auto.conf
>
>;Include AMP configs
>#include zapata_additional.conf
>channel=> 1-15,17-31
>
>signalling=fxo_ks
>context=bank
>group=1
>cas=32-37:1101
>channel=> 32-37
>This is my zapata.conf
>
># Global data
>
>span=1,1,0,ccs,hdb3
>bchan=1-15,17-31
>dchan=16
>
>loadzone        = us
>defaultzone     = us
>
>span=2,1,0,cas,hdb3
>fxols=32-37
>
>
>
>
>-----Original Message-----
>From: asterisk-users-bounces at lists.digium.com
>[mailto:asterisk-users-bounces at lists.digium.com]On Behalf Of Steve
Underwood
>Sent: Tuesday, February 21, 2006 2:59 PM
>To: Asterisk Users Mailing List - Non-Commercial Discussion
>Subject: Re: [Asterisk-Users] Tormenta CAS signaling
>
>
>Viktor Tatianin wrote:
>
>
>
>>Hi Steve
>>
>>I attempt change in  zapata.conf
>>
>>cas=1-15:1101   but use zttool view ABCD bits 1010
>>
>>Regards,
>>Viktor
>>
>>
>>
>>
>Have you put the E1 in CAS mode with something like:
>
>span=1,1,0,cas,hdb3
>
>Steve
>
>
>
>>-----Original Message-----
>>From: asterisk-users-bounces at lists.digium.com
>>[mailto:asterisk-users-bounces at lists.digium.com]On Behalf Of Steve
>>
>>
>Underwood
>
>
>>Sent: Friday, February 10, 2006 3:25 PM
>>To: Asterisk Users Mailing List - Non-Commercial Discussion
>>Subject: Re: [Asterisk-Users] Tormenta CAS signaling
>>
>>
>>Viktor Tatianin wrote:
>>
>>
>>
>>
>>
>>>Hello
>>>
>>>Can anyone know how may change(inverting) cas signaling ABCD bits at the
>>>Tormenta 2 (four E1 ports) cards
>>>My cards send idle code ABCD 0101 but my mux which use as channel bank
>>>
>>>
>wait
>
>
>>>ABCD 1001
>>>
>>>
>>>
>>>
>>>
>>>
>>The idle code is set in zapata.conf. For example:
>>
>>cas=1-15:1101
>>
>>Sets CAS mode for channels 1 to 15, with the idle pattern 1101.
>>
>>Regards,
>>Steve
>>
>>
>>
>>
>
>_______________________________________________
>--Bandwidth and Colocation provided by Easynews.com --
>
>Asterisk-Users mailing list
>To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
>_______________________________________________
>--Bandwidth and Colocation provided by Easynews.com --
>
>Asterisk-Users mailing list
>To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
>

_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users