[Asterisk-Users] Tormenta CAS signaling

[Viktor Tatianin]

Hi Steve
I have next config
zttool

Current Alarms:     No alarms.
Sync Source:        Tormenta 2 (PCI) Quad E1 Card
IRQ Misses:               0
Bipolar Viol:            14
Tx/Rx Levels:         0/  0

Total/Conf/Act:      31/  6/  6
    1111111111222222222333
 1234567890123456789012345789012

  TxA 000000
  TxB 111111
  TxC 000000
  TxD 111111

   RxA 111111
   RxB 011111
   RxC 011111
   RxD 111111







ztcfg -vv

Zaptel Configuration
======================

SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
SPAN 2: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)

Channel map:

Channel 01: Clear channel (Default) (Slaves: 01)
Channel 02: Clear channel (Default) (Slaves: 02)
Channel 03: Clear channel (Default) (Slaves: 03)
Channel 04: Clear channel (Default) (Slaves: 04)
Channel 05: Clear channel (Default) (Slaves: 05)
Channel 06: Clear channel (Default) (Slaves: 06)
Channel 07: Clear channel (Default) (Slaves: 07)
Channel 08: Clear channel (Default) (Slaves: 08)
Channel 09: Clear channel (Default) (Slaves: 09)
Channel 10: Clear channel (Default) (Slaves: 10)
Channel 11: Clear channel (Default) (Slaves: 11)
Channel 12: Clear channel (Default) (Slaves: 12)
Channel 13: Clear channel (Default) (Slaves: 13)
Channel 14: Clear channel (Default) (Slaves: 14)
Channel 15: Clear channel (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: Clear channel (Default) (Slaves: 17)
Channel 18: Clear channel (Default) (Slaves: 18)
Channel 19: Clear channel (Default) (Slaves: 19)
Channel 20: Clear channel (Default) (Slaves: 20)
Channel 21: Clear channel (Default) (Slaves: 21)
Channel 22: Clear channel (Default) (Slaves: 22)
Channel 23: Clear channel (Default) (Slaves: 23)
Channel 24: Clear channel (Default) (Slaves: 24)
Channel 25: Clear channel (Default) (Slaves: 25)
Channel 26: Clear channel (Default) (Slaves: 26)
Channel 27: Clear channel (Default) (Slaves: 27)
Channel 28: Clear channel (Default) (Slaves: 28)
Channel 29: Clear channel (Default) (Slaves: 29)
Channel 30: Clear channel (Default) (Slaves: 30)
Channel 31: Clear channel (Default) (Slaves: 31)
Channel 32: FXO Loopstart (Default) (Slaves: 32)
Channel 33: FXO Loopstart (Default) (Slaves: 33)
Channel 34: FXO Loopstart (Default) (Slaves: 34)
Channel 35: FXO Loopstart (Default) (Slaves: 35)
Channel 36: FXO Loopstart (Default) (Slaves: 36)
Channel 37: FXO Loopstart (Default) (Slaves: 37)

37 channels configured.

this is zaptel.conf

; Zapata telephony interface
;
; Configuration file

[trunkgroups]

[channels]

language=en
context=from-isdn-external
;signalling=fxs_ks
;rxwink=300             ; Atlas seems to use long (250ms) winks
signalling=pri_cpe
switchtype=euroisdn
pridialplan=unknown
prilocaldialplan=unknown
callerid=asreceived
usedistinctiveringdetection=yes
usecallingpres=yes

; Whether or not to do distinctive ring detection on FXO lines
;
;usedistinctiveringdetection=yes

usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
echotraining=400
rxgain=0.0
txgain=0.0
group=0
callgroup=1
pickupgroup=1
immediate=no

;faxdetect=both
faxdetect=incoming
;faxdetect=outgoing
;faxdetect=no

;Include genzaptelconf configs
#include zapata-auto.conf

;Include AMP configs
#include zapata_additional.conf
channel=> 1-15,17-31

signalling=fxo_ks
context=bank
group=1
cas=32-37:1101
channel=> 32-37
This is my zapata.conf

# Global data

span=1,1,0,ccs,hdb3
bchan=1-15,17-31
dchan=16

loadzone        = us
defaultzone     = us

span=2,1,0,cas,hdb3
fxols=32-37




-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com]On Behalf Of Steve Underwood
Sent: Tuesday, February 21, 2006 2:59 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [Asterisk-Users] Tormenta CAS signaling


Viktor Tatianin wrote:

>Hi Steve
>
>I attempt change in  zapata.conf
>
>cas=1-15:1101   but use zttool view ABCD bits 1010
>
>Regards,
>Viktor
>
>
Have you put the E1 in CAS mode with something like:

span=1,1,0,cas,hdb3

Steve

>-----Original Message-----
>From: asterisk-users-bounces at lists.digium.com
>[mailto:asterisk-users-bounces at lists.digium.com]On Behalf Of Steve
Underwood
>Sent: Friday, February 10, 2006 3:25 PM
>To: Asterisk Users Mailing List - Non-Commercial Discussion
>Subject: Re: [Asterisk-Users] Tormenta CAS signaling
>
>
>Viktor Tatianin wrote:
>
>
>
>>Hello
>>
>>Can anyone know how may change(inverting) cas signaling ABCD bits at the
>>Tormenta 2 (four E1 ports) cards
>>My cards send idle code ABCD 0101 but my mux which use as channel bank
wait
>>ABCD 1001
>>
>>
>>
>>
>The idle code is set in zapata.conf. For example:
>
>cas=1-15:1101
>
>Sets CAS mode for channels 1 to 15, with the idle pattern 1101.
>
>Regards,
>Steve
>
>

_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users