[Asterisk-Users] Analog with channel bank - Inbound works, outbound doesn't

[C F]

Then I got no clue how to configure it. But it looks like something is
wrong in that setup there.

On 2/1/06, james.texter at cox.net <james.texter at cox.net> wrote:
> No, it's an Access Bank II SNMP.
>
> Thanks,
>
> James
>
> C F wrote:
> > Is this an Adit 600?
> >
> > On 2/1/06, james.texter at cox.net <james.texter at cox.net> wrote:
> >> The output from the CLI when I put in an inbound call is the following:
> >>
> >>    -- Starting simple switch on 'Zap/25-1'
> >>    -- Executing GotoIf("Zap/25-1", "1?from-pstn-reghours|s|1:") in new stack
> >>    -- Goto (from-pstn-reghours,s,1)
> >>    -- Executing GotoIf("Zap/25-1", "0?from-pstn-reghours-nofax|s|1:2") in new stack
> >>    -- Goto (from-pstn-reghours,s,2)
> >>    -- Executing Answer("Zap/25-1", "") in new stack
> >>    -- Executing Wait("Zap/25-1", "1") in new stack
> >>    -- Executing SetVar("Zap/25-1", "intype=EXT-412") in new stack
> >>    -- Executing Cut("Zap/25-1", "intype=intype|-|1") in new stack
> >>
> >> It then goes on to call the extension I have setup.  I think it's coming in on Channel 25, but I'm not sure what the -1 is for in Zap/25-1.
> >>
> >> Not sure if this is relevant or not, but I'm using a Carrier Access Corporation (CAC) channel bank, with 1 FXO card and 1 FXS card.  The analog line is definitely hooked to the FXO card, and I definitely have the T1 plugged in to the FXO card.
> >>
> >> Thanks,
> >>
> >> James
> >>
> >>
> >> C F wrote:
> >>> Looks like  channel 25 is not the one hooked up to your POTS, when an
> >>> incoming call arrives, what channel does the CLI report?
> >>>
> >>>
> >>> On 2/1/06, james.texter at cox.net <james.texter at cox.net> wrote:
> >>>> Thanks for the reply.  I have tried adding anywhere between 1 and 6 w's to the dial string, but still no luck.  I hooked up and listened on the line when the call went out, and never heard any DTMF's.  I'm sure this must be something simple, I just can't seem to figure out for the life of me what it is.  What other information can I provide to help sort this out?
> >>>>
> >>>> Thanks again,
> >>>> James
> >>>>
> >>>> ------------------------------
> >>>> You could insert a pause by adding a w before the number to be dialed,
> >>>> like this:
> >>>> Dial(zap/25/w1234567890) iirc each w puts a 500ms pause.
> >>>>
> >>>>
> >>>> On 1/30/06, james.texter at cox.net <james.texter at cox.net> wrote:
> >>>>>> I am experimenting with an asterisk setup in my office.  The last bit I have to test is working with analog lines.  I have TE411p digium card, with an ISDN line plugged into the first, a channel bank plugged into the second port, and the last two ports empty.  I have the following setup in my zaptel.conf:
> >>>>>>
> >>>>>> span=1,1,0,esf,b8zs
> >>>>>> bchan=1-23
> >>>>>> dchan=24
> >>>>>>
> >>>>>> span=2,0,0,d4,ami
> >>>>>> fxsks=25
> >>>>>>
> >>>>>> And in zapata.conf, I have:
> >>>>>> group=2
> >>>>>> language=en
> >>>>>> context=from-pstn
> >>>>>> signalling=fxs_ks
> >>>>>> channel=>25
> >>>>>>
> >>>>>> I have one analog line plugged in for testing.  If I dial that analog number, the inbound call arrives, and it works great.  However, when I place an outbound call, I get the following output:
> >>>>>> -- Called g2/5148346
> >>>>>> -- Zap/25-1 answered SIP/412-9b72
> >>>>>>
> >>>>>> However, my number never rings.  After about 30 seconds, I get a message saying my call could not be completed as dialed.  Almost like it didn't get all of the digits.  Is there a way to inject a pause before dialing?  Any other thoughts?  Any help is greatly appreciated.
> >>>>>>
> >>>>>> _______________________________________________
> >>>>>> --Bandwidth and Colocation provided by Easynews.com --
> >>>>>>
> >>>>>> Asterisk-Users mailing list
> >>>>>> To UNSUBSCRIBE or update options visit:
> >>>>>>    http://lists.digium.com/mailman/listinfo/asterisk-users
> >>>>>>
> >>>> _______________________________________________
> >>>> --Bandwidth and Colocation provided by Easynews.com --
> >>>>
> >>>> Asterisk-Users mailing list
> >>>> To UNSUBSCRIBE or update options visit:
> >>>>    http://lists.digium.com/mailman/listinfo/asterisk-users
> >>>>
> >>>>
> >>>> _______________________________________________
> >>>> --Bandwidth and Colocation provided by Easynews.com --
> >>>>
> >>>> Asterisk-Users mailing list
> >>>> To UNSUBSCRIBE or update options visit:
> >>>>    http://lists.digium.com/mailman/listinfo/asterisk-users
> >>>>
> >>> _______________________________________________
> >>> --Bandwidth and Colocation provided by Easynews.com --
> >>>
> >>> Asterisk-Users mailing list
> >>> To UNSUBSCRIBE or update options visit:
> >>>    http://lists.digium.com/mailman/listinfo/asterisk-users
> >>>
> >>
> >> _______________________________________________
> >> --Bandwidth and Colocation provided by Easynews.com --
> >>
> >> Asterisk-Users mailing list
> >> To UNSUBSCRIBE or update options visit:
> >>   http://lists.digium.com/mailman/listinfo/asterisk-users
> >>
> > _______________________________________________
> > --Bandwidth and Colocation provided by Easynews.com --
> >
> > Asterisk-Users mailing list
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-users
> >
>
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>