[Asterisk-Users] Asterisk & Lucent TNT w/11.0.2

[Dave Weis]

On Sat, 5 Nov 2005, Shane DeRidder wrote:
> I've been scouring the mailing list archives for an answer to this, and
> cannot find one.  I'm hoping someone else out there has run into this.
> Communication between the TNT and Asterisk seems to be operating
> properly, but I'm unable to accept or originate calls.  When I attempt
> to dial out, I see the following in the TNT's syslog:
>
> 10.0.0.10  = TNT
> 10.0.0.103 = Asterisk
>
> new MEDIA-GATEWAY
> set name = voip
> set active = yes
> set protocol-type = sip
> set mg-sig-address type = specific

> set mg-sig-address ip-address = 10.0.0.10
> set mg-rtp-address ip-address = 10.0.0.10

I have these set to what would be 10.0.0.103 on my TNT and it's working.

dave

> set transport-options type = udp
> set transport-options heartbeat = yes
> set voip-options codec-options g711-ulaw dtmf-tone-passing = rtp
> set voip-options codec-options g711-ulaw silence-det-cng = yes
> set sip-options primary-proxy ip-address = 10.0.0.103
> set sip-options primary-proxy transport-options heartbeat = yes
> set sip-options registration-proxy ip-address = 10.0.0.103
> set sip-options unknown-ani = 0000000000
> set sip-options unknown-name = Unknown
> set sip-options blocked-ani = 0000000000
> set sip-options blocked-name = Blocked
> write -f
>
> My 12 T1/PRI are configured exactly alike:
>
> new T1
> set name = PRI-0
> set physical-address shelf = shelf-1
> set physical-address slot = slot-1
> set physical-address item-number = 1
> set line-interface enabled = yes
> set line-interface frame-type = esf
> set line-interface encoding = b8zs
> set line-interface signaling-mode = isdn
> set line-interface default-call-type = dnis-or-voip
> set line-interface switch-type = nat-isdn-2-pri
> set line-interface front-end-type = csu
> set line-interface channel-config 24 channel-usage = d-channel
> set line-interface collect-incoming-digits = yes
> set line-interface voip-gain-control output-pad = 9db-loss
> set line-interface media-gateway = voip
> set line-interface egress-ani-dnis-format = dnis
> write -f
>
> Asterisk sip.conf:
>
> [maxtnt]
> type=friend
> host=10.0.0.10
> dtmfmode=inband
> callerid="MaxTNT" <maxtnt>
> context=toll-access
> qualify=yes
> reinvite=no
> canreinvite=no
> disallow=all
> allow=g729
> allow=ulaw
>
> [xxxxxxx]
> type=friend
> host=dynamic
> nat=yes
> callerid=Name <xxxxxxx>
> context=toll-access
> dtmfmode=info
> call-limit=1
> mailbox=xxxxxxx at default
> disallow=all
> allow=g729
> allow=ulaw
>
> Asterisk extensions.conf:
>
> [toll-trunks]
> exten => _1NXXNXXXXXX,1,Dial(SIP/${EXTEN}@10.0.0.10,60)
> exten => _1NXXNXXXXXX,2,Hangup
>
> [local-trunks]
> exten => _NXXXXXX,1,Dial(SIP/${EXTEN}@10.0.0.10,60)
> exten => _NXXXXXX,2,Hangup
>
> [local-access]
> include => extensions
> include => local-trunks
>
> [toll-access]
> include => local-access
> include => toll-trunks
>
>
> I apologize if this is considered off-topic.  My thoughts are that I
> have a problem with the configuration of my TNT and not Asterisk itself.
>
>

-- 
Dave Weis             "I believe there are more instances of the abridgment
djweis at sjdjweis.com   of the freedom of the people by gradual and silent
                       encroachments of those in power than by violent
                       and sudden usurpations."- James Madison