[Asterisk-Users] TE410P problem (Looping UP Span 1...) [digium.com #13999]

[Peter Childs]

 The the 'common' factor here appers to be the Intel E7520 Chipset.

 I have a NEC 120Rg-2 here with this chipset with the same problem.

 This chipset exists in the HP DL380 G4 Server, and the machine
 mentioned below.

 Someone else mentioned the same issue on a new Dual Xeon EM64T
 capable Tatung server, and some searching on their website shows
 TSS-2552 also uses the Intel E7520 Chipset....

 Perhaps its just coincidence?

 Cheers,
  Peter

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com]On Behalf Of Sid
Sent: Tuesday, 11 January 2005 7:35 AM
To: Eric Bishop; Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [Asterisk-Users] TE410P problem (Looping UP Span 1...)


Hi,

This is the motherboard:
SM X6DAE-XG2 Dual XEON 800FSB EMT64 w/2-Ch SATA-R 0&1,SVGA,2xGb LAN
Dual Intel. Xeon EM64T Support up to 3.60 GHz
Intel. E7520 (Lindenhurst) Chipset
1(x8) PCI-Express on (x16) Slot, 3 x 64-bit 133MHz PCI-X, 2 x 64-bit 100MHz
PCI-X Slots
ATI RageXL 8MB Graphics

Actually it doesnt have 4 cpus as i mentioned in my earlier mail. It has 2
XEON cpus with
hyper-threading technology. Anyone has seenexperienced any problems with
this
motherboard?

-Sid

--- Eric Bishop <asterisk.eric at gmail.com> wrote:

> Is it a HP-Compaq DLXXX G4 machine? Because there is a thread here
> about the TE410P not generating interrupts with these servers...
>
>
> On Sat, 8 Jan 2005 05:14:39 -0800 (PST), Sid <avoips at yahoo.com> wrote:
> > Hi Scott, and Jack,
> >
> > --- Scott Stingel <scott at evtmedia.com> wrote:
> >
> > > Sid-
> > >
> > > Try connecting one port to another.  Note that one of the ports must
be
> > > set up as "cpe" and the other as "net" in zapata.conf when you loop
them
> > > together like this.
> > >
> > > A suitable crossover cable for testing can be constructed by cutting
up
> > > a CAT 5 cable, and connecting:
> > > Pin 1 <--> Pin 4 on the other end
> > > Pin 2 <--> Pin 5
> > > Pin 4 <--> Pin 1
> > > Pin 5 <--> Pin 2
> > >
> > > You should get green's on both the connected channels if your zaptel
and
> > > zapata configurations are ok, and if you've run both modprobe and
ztcfg
> > > as documented.
> > >
> >
> > Thanks for the valuable responses. We can only do the tests on monday,
as the machine
> is
> > in a data center. Other than that we have done every tests we can think
of and found
> in
> > the mailing list/wiki. The tests done at the NOC says that T1 is ok at
their end.
> Please
> > see the following information about the system:
> >
> > The machine has 4 Xeon 2.80GHz CPUs.
> >
> > This is from /proc/interrupts
> >  16:          0          0          0          3   IO-APIC-level
usb-uhci
> >  19:          0          0          0          0   IO-APIC-level
usb-uhci
> >  23:          0          0          0          0   IO-APIC-level
ehci-hcd
> >  26:     129024          0          0         28   IO-APIC-level  eth1
> >  27:          0          0      21352          5   IO-APIC-level  eth0
> >  76:          0          0          0          0   IO-APIC-level  t4xxp
> >
> > # dmesg
> > Zapata Telephony Interface Registered on major 196
> > Specify address with base=0xNNNNN
> > Registered Tormenta2 PCI
> > Found TE410P at base address fc8ff800, remapped to f8a40800
> > TE410P version c01a009b
> > FALC version: 00000005, Board ID: 00
> > Reg 0: 0x371c9800
> > Reg 1: 0x371c9000
> > Reg 2: 0x07fc07fc
> > Reg 3: 0x00000000
> > Reg 4: 0x00000000
> > Reg 5: 0x00000000
> > Reg 6: 0xc01a009b
> > Reg 7: 0x00001000
> > Reg 8: 0x00000000
> > Reg 9: 0x00ff0000
> > Reg 10: 0x00000000
> > TE410P: Launching card: 0
> > TE410P: Setting up global serial parameters
> > Found a Wildcard: Wildcard TE410P-Xilinx
> > Registered tone zone 0 (United States / North America)
> > TE410P: Span 1 configured for ESF/B8ZS
> > SPAN 1: Primary Sync Source
> >
> > I am doubtful about the interrupts. Are those values ok? We have been
after this
> problem
> > for more than a week now, we have tested with 2 different cards to no
success.
> >
> > I'll post the results of the crossover connection test, once we do that.
Thanks again
> for
> > the responses.
> >
> > BR,
> > -Sid


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users